Connecting the Battery Cables
$"-*'03/*"130104*5*0/8"3/*/(
#BUUFSZQPTUTUFSNJOBMTBOESFMBUFEBDDFTTPSJFT
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
$"65*0/
When attaching battery cables, always
DPOOFDUUIF104*5*7& 3FEXJSFUPJUTUFSNJOBMGJSTU
GPMMPXFECZUIF/&("5*7& #MBDLXJSF
For shipping reasons, both battery cables on your equipment
may have been left disconnected from the terminals at the
factory. To connect the battery cables, proceed as follows:
NOTE:
5IFQPTJUJWFCBUUFSZUFSNJOBMJTNBSLFE1PT 5IF
OFHBUJWFCBUUFSZUFSNJOBMJTNBSLFE/FH o
NOTE:
If the positive battery cable is already attached, skip ahead
to step 2.
Remove the plastic cover, if present, from the positive
1.
CBUUFSZUFSNJOBMBOEBUUBDIUIFSFEDBCMFUPUIFQPTJUJWF
battery terminal with the bolt and hex nut. See Fig. 3-2.
3FNPWFUIFQMBTUJDDPWFSJGQSFTFOUGSPNUIFOFHBUJWF o
2.
battery terminal and attach the black cable to the negative
oCBUUFSZUFSNJOBMXJUIUIFCPMUBOEIFYOVU4FF'JH
1PTJUJPOUIFSFESVCCFSCPPUPWFSUIFQPTJUJWFCBUUFSZ
3.
terminal to help protect it from corrosion.
NOTE:
If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in the
.BJOUFOBODFTFDUJPOZPVS0QFSBUPST.BOVBMQSJPSUPPQFSBUJOH
the tractor.
Checking Tire Pressure
8"3/*/(
Do not overinflate tires. Check sidewall
of tires for maximum psi. Equal tire pressure should
be maintained at all times.
The tires on your tractor may be over inflated for shipping
purposes. Reduce the tire pressure before operating the tractor.
Check sidewall of tires for maximum psi.
Setting the Deck Gauge Wheels
Move the tractor on a firm and level surface, preferably
pavement, and proceed as follows
Select the height position of the cutting deck by placing
1.
the deck lift lever in the normally desired mowing height
setting (any of the six different cutting height notches on
the right fender).
Check the gauge wheels for contact or excessive clearance
2.
with the surface below. The deck gauge wheels should
IBWFCFUXFFOwBOEwDMFBSBODFBCPWFUIFHSPVOE
If the gauge wheels have excessive clearance or contact
3.
with the surface, adjust as follows:
Raise the deck lift handle to its highest setting.
a.
Remove the front and rear gauge wheels by
b.
removing the lock nuts and shoulder screws which
secure them to the deck. See Fig. 3-3.
1MBDFUIFEFDLMJGUMFWFSJOUIFEFTJSFENPXJOH
c.
height setting.
Reinsert the shoulder screw (with each gauge
d.
wheel) into the index hole that leaves approximately
wCFUXFFOUIFCPUUPNPGUIFXIFFMBOEUIF
pavement.
Refer to Leveling the Deck in the Maintenance section of this
manual for more detailed instructions regarding various deck
adjustments.
'JHVSF
'JHVSF
S
ECTION
2 — A
SSEMBLY
& S
ET
-U
P