WhisperKool InCellar 8000 Скачать руководство пользователя страница 7

Страница: 7 / 38

www.whisperkool.com | Page 5

INTRODUCTION

Customer Service

Thank you for purchasing a WhisperKOOL InCellar Series cooling unit. We strive to provide the highest quality

products and the best possible customer service. If you have any questions about your WhisperKOOL unit, please call

us at 1(800) 343-9463 or visit whisperkool.com.

Using the Manual

This User’s Manual is intended to assist in the proper installation and maintenance of the WhisperKOOL cooling unit.

In order to ensure the longevity of your cooling unit, the equipment should be installed properly and have a proper

care and maintenance schedule. Please read and review this manual carefully and keep it for future reference.

What Is the WhisperKOOL Cooling Unit?

The WhisperKOOL unit is a specialized refrigeration unit designed for one purpose only: to maintain the optimal

temperature and humidity levels conducive to the proper storage and aging of fine wines. It is a self-contained

cooling unit designed to be used as a forced-air partially ducted system.

How Does the WhisperKOOL InCellar Series Work?

The WhisperKOOL unit is epecially designed for the use and application to maintain optimal conditions for wine

storage and aging. The unit is fully self-contained and is designed to be installed completely inside the wine cellar.

The unit draws air in from an adjacent room and exhausts heat via duct work to an acceptable area. This provides the

ease of installation of a through the wall system, while keeping unwanted noise and heat to a minimum. All InCellar

units are temperature controlled via a bottle probe and come standard with an advanced digital thermostat.

Temperature Setting

The WhisperKOOL InCellar unit can be set at any temperature within the acceptable wine-aging range of 50°F to 70°F.

It is designed to cool up to 55°F cooler than the ambient temperature of the space to which it is exhausting.

Содержание InCellar 8000







































Результаты поиска

Содержание InCellar 8000

Отзывы:

Похожие инструкции для InCellar 8000

Бренды по названию

Популярные бренды

WhisperKool InCellar 8000, Руководство пользователя

Результаты поиска

Содержание InCellar 8000

Отзывы:

Похожие инструкции для InCellar 8000

Бренды по названию

Популярные бренды