background image

 
 
 
 
 
SPARE PARTS LIST 

 

 

 

38

 

December 2010 / M-SC6/8/10 / EN 

 

6  SPARE PARTS LIST  

 
A parts manual in English is available as an option number: number: 40200381 (***)(M-SC6 and 8); 40200382(***) (M-SC10). 
A work shop manual in English is available as an option  number: 40200171. 
We recommend the following spares for service and maintenance. 
• Kit A: parts for regular maintenance parts (M-SC6, 8 and 10) marked  

(*)  

article no. 40201860  

• Kit B: parts for maint spare parts:(M-SC6 and 8) all parts market  

(*)+(**)  

article no. 40201861 

• Kit C: parts for "world travellers" all parts market (M-SC6 and 8) 

(*)+(**)+(***)  

article no. 40201862 

• Kit B: parts for maint spare parts: all parts market (M-SC10)  

(*)+(**)  

article no. 40201761 

• Kit C: parts for "world travellers" all parts market (M-SC10)  

(*)+(**)+(***) 

article no. 40201762  

 

 

ARTICLE NO 

DESCRIPTION  

 

40209030 

Fuel filter (*)   

 

50201060 

Fuel lift pump (***)   

 

50203120 

V-belt (*)   

 

40203121  

Oil filter (*)   

 

50201850 

Raw water pump complete WhisperPower type M (***)  (refer to fig. 26)   

 

40209011 

Im gasket (*) (4,3,5)   

 

40201812 

Cover type M (**) (2)   

 

50209018 

Bolts cover (**) (1) (6 pcs.)   

 

40201851  

Pump repair kit A consisting of: Shaft (50201811), Bearings (2 pcs) (50209014), O-ring (50209017), 
Seals (2 pcs.) (50209015), Clips (1 set) (50209019), O-ring (50201814)  

 

40209010  

Pump repair kit B (**)(same as repair kit A excluding the shaft (50201811) and O-ring (50201814))  

 

50201820  

Heat exchanger complete with appendages (M-SC6 and 8)(***)  

 

50201822  

Water hoses with clamps (M-SC6 and 8) (**)  

 

50201720  

Heat exchanger complete with appendages (M-SC10)(***)  

 

50201722  

Water hoses with clamps (M-SC10) (**)  

 

 

Capacitor xx micro-farad, 2 pcs (**) (xx = give value when ordering)  

 

50209132  

Measuring coil (***)  

 

50201890  

Rotary diode (**)  

 

50101886  

Alternator bearing including O-ring (**)  

 

 

Voltage regulator (M-SC8 and 10)(optional)  

 

40209161  

Local control panel (***)  

 

50209146 

Digital Diesel Control Unit (***)  

 

50212170  

Fuses 10 Amps(*)  

 

50212154  

Fuses 3 Amps (*)  

 

50201886  

Wiring loom complete (***)  

 

40209102  

Digital Diesel Remote control panel (***)  

 

50209133 

Cable remote control 15 mtr, including connectors  

 

50203033  

Overhaul gasket kit / Sealkit (M-SC6 and 8) (***)  

 

50203030  

Cylinder head gasket kit (M-SC6 and 8)  

 

50204033  

Overhaul gasket kit / Sealkit (M-SC10) (***)  

 

50204030  

Cylinder head gasket kit (M-SC10)   

 

50203040  

Glow plug, 2 pcs (M-SC6 and 8) (**); 3pcs (M-SC10) (**)  

 

50203050  

Nozzle injector, 2 pcs (M-SC6 and 8) (**); 3pcs (M-SC10) (**)  

 

50203160  

Fuel pump (high pressure) complete (M-SC6 and 8) (***)  

 

50204160  

Fuel pump (high pressure) complete (M-SC10) (***)  

 

50203045  

Thermostat (**)  

 

50203038  

Gasket thermostat (**)  

 

50203037  

Gasket rockercover (M-SC6 and 8) (**)  

 

50204037  

Gasket rockercover (M-SC10) (**)  

 

50209051  

Silicone O-ring soundshield cover (**)  

More extensive parts list on the internet: WHISPERPOWER.EU (fast moving parts) 

Содержание M-SC6













































Отзывы: