10
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
TROUBLESHOOTING
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
The dishwasher
won’t start
or does not
respond to com-
mands.
The appliance has not been plugged in properly.
Insert the plug into the socket.
Power outage.
The dishwasher starts automatically when the power returns.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
It does not respond to commands.
Switch off the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
The door doesn’t
lock.
Racks are not fit to the end.
Verify that racks are fit to the end.
The door is not lock.
Vigorously push the door until you hear the “clack” sound.
The dishwasher
makes excessive
noise.
The dishes are rattling against each.
Position the crockery correctly
(see LOADING THE RACKS).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Reset the current cycle by switching OFF the dishwa-
sher, then switch it on again, select a new program, press START
and close the door. Please do not add any detergent.
The dishes have
not been dried.
The selected program hasn’t any drying phase.
Verify on the programs table if the selected program has the drying
phase.
The rinse aid has run out or the resolution is not
adequate.
Add the rinse aid or adjust the dosage levels higher
(see FILLING
THE RINSE AID DISPENSER).
The dishes are made of non-stick or plastic.
It is normal the presence of drops of water
(see TIPS)
.
The dishes are
not clean.
The crockery has not been arranged properly.
Arrange the crockery correctly
(see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered
by the dishes.
Arrange the crockery correctly
(see LOADING THE RACKS).
The wash cycle is too gentle.
Select an appropriate wash cycle
(see PROGRAMS TABLE).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not suita-
ble for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
Clean the filter assembly
(see CARE AND MAINTENANCE).
There is no salt.
Fill the salt reservoir
(see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the
water, shows
„H2O” Warning
or „F06”
No water in the water supply or the tap is closed.
Make sure there is water in the water supply or the tap running.
The inlet hose is bent.
Make sure there is water in the water supply or the tap running.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and
turn on the dishwasher and restart a new program.
The dishes and
glasses show
calcination or a
whitish film.
The salt level is too low.
Fill the salt reservoir
(see FILLING THE SALT RESERVOIR).
The adjustment of the water hardness is not adequate. Increase the values
(see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed.
Check to have properly closed the salt reservoir cap.
The rinse aid is used up or the dosage is insufficient.
Add the rinse aid or adjust the dosage levels higher.
The dishes and
glasses are blue
streaked or have
a bluish tinge.
The rinse aid dosage is excessive.
Adjust the dosage rates below.
Содержание WSIP 4O33 PFE
Страница 12: ...12 400011264245B 07 2018 as Xerox Fabriano ...
