4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■
Tape measure
■
Phillips screwdriver
■
Flat-blade screwdriver
■
1/8" (3 mm) flat-blade
screwdriver
■
Level
■
Drill
■
Wrench or pliers
■
Pipe wrench
■
15/16" (24 mm) combination
wrench
■
1/8" (3.2 mm) drill bit
(for wood floors)
■
Marker or pencil
Parts Supplied
Check that all parts are included.
■
Propane/Natural Gas Conversion Kit
■
#10 x 1
5
/
8
" (41.3 mm) screws
(for mounting anti-tip bracket) (2)
■
Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to anchor
bracket to subfloor. Longer screws are available from your local
hardware store.
■
For Models:
WEG750H0H
WEGA25H0H
Burner Caps
5
Burner Grates
2
Oven Racks
3
Parts Needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the “Electrical Requirements”
and “Gas Supply Requirements” sections.
IMPORTANT:
When the range is used under microwave models:
JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door
Baffle Plate Part Number W10737014 must be ordered and
used. Please reference the “Accessories” section of the User
Guide for contact information.
■
Pipe-joint compound
resistant to propane gas
■
3/16" (4.8 mm) carbide-
tipped masonry drill bit
(for concrete/ceramic
floors)
■
Noncorrosive leak-
detection solution
For Propane/Natural Gas
Conversions
■
5/8" (16 mm) combination
wrench
■
3/8" (95 mm) nut driver
■
9/32" (7 mm) nut driver
■
Masking tape
Optional Parts
To purchase these or any other accessories, please reference the
“Accessories” section of the User Guide for contact information.
■
Side Trim Kits:
5/8" (15.88 mm) White - Order Part Number W10675027
5/8" (15.88 mm) Black - Order Part Number W10675026
5/8" (15.88 mm) Stainless Steel - Order Part Number
W10675028
1
1
/
8
" (2.9 cm) White - Order Part Number W10731885
1¹⁄
8
" (2.9 cm) Black - Order Part Number W10731886
1¹⁄
8
" (2.9 cm) Stainless Steel - Order Part Number
W10731887
■
Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
Location Requirements
IMPORTANT:
Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
■
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on
the top right-hand side of the oven frame.
■
The range should be located for convenient use in the
kitchen.
■
Recessed installations must provide complete enclosure of
the sides and rear of the range.
■
All openings in the wall or floor where range is to be installed
must be sealed.
■
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
■
The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see “Install Anti-Tip Bracket”
section.
■
Grounded electrical supply is required. See the “Electrical
Requirements” section.
■
Proper gas supply connection must be available. See the
“Gas Supply Requirements” section.
■
Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
■
Use an insulated pad or 1/4" (6.4 mm) plywood under range
if installing range over carpeting.
IMPORTANT:
To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
Содержание WEG750H0HB
Страница 70: ...70 Notas ...
Страница 71: ...71 Notas ...
