background image

13

Good

Better

Clamps:

Use clamps to seal all joints.

 

Exhaust vent must not be connected or secured with screws 

 

or other fastening devices that extend into interior of duct 

and catch lint. Do not use duct tape.

An exhaust hood should cap vent to keep rodents  

 

and insects from entering home.

Do not use exhaust hood with a magnetic latch.

 

Elbows:

45° elbows provide better airflow than 90° elbows.

 

Vent products can be purchased from your dealer. For further 

information, see “Assistance or Service” section in your Use  

and Care Guide.

pLAN vENT SYSTEM

Choose your exhaust installation type

Recommended exhaust installation:

Periscope installation

Over-the-top installation  

(also available with one offset elbow)

 Bottom exhaust installation

Special provisions for mobile homes:

Exhaust vent must be securely fastened to a noncombustible 

portion of mobile home and must not terminate beneath  

the mobile home. Terminate exhaust vent outside. 

Alternate exhaust installations (for close clearance):

Vent systems come in many varieties. Select the type best  

for your installation. Refer to the manufacturer’s instructions.

Содержание WED7990XU

















Отзывы: