Whirlpool JOB AID GC1SHAXM Скачать руководство пользователя страница 38

Страница: 38 / 56

6-2

SUGGESTIONS ON DIAGNOSIS

IMPORTANT:

1. Check harness connectors for good con-

tact.

2. Before replacing any component verify,

whenever possible, that the component
has proper continuity or resistance values.
There must be proper power to operate the
component.

Display Shows Error Codes

• If error codes “C”, “d” or “CF” show in the

display, refer to the “User Interface Failure
Feedback” and “Component Testing” charts
and check out the appropriate compo-
nent(s).

Display Is Normal

• Disconnect power for 10 seconds and re-

connect power. If error code is displayed
after 3 minutes, refer to the “User Interface
Failure Feedback” and “Component Test-
ing” charts, and check out the appropriate
component(s).

• If no error codes display and a malfunction

is occurring, check or troubleshoot the fol-
lowing appropriate areas. Also refer to the
“Component Testing” and “Troubleshooting”
charts.

-  Electrical system
-  Restricted or lack of proper airﬂow
-  Defrost system
-  Unusual noises
-  Cooling system

Display Is Blank

• Refer to “User Interface Failure Feedback”

and “Troubleshooting” charts.

Содержание JOB AID GC1SHAXM

























































Результаты поиска

Содержание JOB AID GC1SHAXM

Отзывы:

Похожие инструкции для JOB AID GC1SHAXM

Бренды по названию

Популярные бренды

Whirlpool JOB AID GC1SHAXM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание JOB AID GC1SHAXM

Отзывы:

Похожие инструкции для JOB AID GC1SHAXM

Бренды по названию

Популярные бренды