Whirlpool ImPress LFB2611L Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

Whirlpool ImPress LFB2611L Скачать руководство пользователя страница 15

COMPONENT ACCESS

REMOVING THE LIGHT SOCKET, INDICATOR LIGHT,

TIMER, AC RECEPTACLE, & CUTOFF SWITCH

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

NOTE:

Sharp edges may be present.

1.

Disconnect the power to the ironing sta-
tion.

NOTE: The location of the components that are
serviced in this section are shown below:

Indicator Light

Timer

AC Receptacle

Cutoff Switch

2.

Lift and remove the iron storage wedge
from the unit.

Mounting Screw
(1 of 3)

Component Cover

4-1

Continued on the next page.

Protective

Cover

Light Lens &
Light Socket

3.

Lower the ironing board.

4.

Place a towel or something similar on top
of the ironing board to protect it.

5.

Remove the three mounting screws from
the component cover and remove the
cover from the bracket. Lay the compo-
nent cover on the protective ironing board
cover as shown below.

Iron Storage Wedge

Iron Storage Wedge

Component Cover

«
...
13
14
15
16
17
...
»

Содержание ImPress LFB2611L

























Отзывы:

Нет отзывов