Whirlpool ImPress LFB2611L Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

background image

PRODUCT OPERATION

ADJUSTING THE BOARD HEIGHT

1.

Pull the top of the board forward several
inches.

2.

To raise the board:

a) Grasp the top of the board frame, pull

the board forward an inch or so, and
lift the frame slightly to unlock the posi-
tioning rod.

b) Push the positioning rod in and slide it

to the back of the slots in the side brack-
ets.

c) Lift the positioning rod to the upper slot

position, then pull the rod forward as
far as the slot allows.

3.

Rotate the front of the board down to its
ironing position.

ADJUSTING THE SWIVEL TENSION

The ironing board can be rotated 360

°

by

moving the front to the left or right. The tension
knob under the board may have to be loosened
to obtain a comfortable swivel tension. To
adjust the tension, turn the knob clockwise
(tighten), or counterclockwise (loosen).

Upper
Position

THE WORK LIGHT

A work light is activated when the ironing
board is placed in a horizontal position and
the timer is turned on.

Tension Knob

Lower
Position

3-1

Positioning Rod

Board Frame

Lift Frame

Pull Board
Out 1 to 2

″

Work
Light

«
...
11
12
13
14
15
...
»

Содержание ImPress LFB2611L

























Отзывы:

Нет отзывов

Похожие инструкции для ImPress LFB2611L

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды