Whirlpool Gold WFD193 Скачать руководство пользователя

Страница: 5 / 52

Component Identification

Product Application

This furnace is primarily designed for residential home-heating
applications.

IMPORTANT:

■

This furnace is not designed or certified for use in mobile
homes, trailers or recreational vehicles.

■

This furnace is not designed or certified for outdoor
applications.

■

The furnace must be installed indoors (for example, attic
space, crawl space or garage area provided the garage area
is enclosed with an operating door).

This furnace can be used in the following nonindustrial
commercial applications:

NOTE: In such applications, the furnace must be installed with
the following stipulations:

■

It must be installed according to the installation instructions
provided and according to local and national codes.

■

It must be installed indoors in a building constructed on site.

■

It must be part of a ducted system and not used in a free air
delivery application.

■

It must not be used as a “makeup” air unit.

■

It must be installed with 2-pipe systems for combustion air,
especially if VOC’s or other contaminants are present in the
conditioned space.

■

All other warranty exclusions and restrictions apply.

A. Gas control valve
B. Gas line entrance (alternate)

C. Pressure switch
D. Gas manifold

E. Combustion air intake

connection/coupling

F. Hot surface igniter

G. Rollout limit switch
H. Burners

I. Flame sensor

J. Flue pipe connection/coupling

K. Flue pipe

L. Primary limit switch

M. Gas line entrance

N. Flue pipe connection (alternate)
O. Rubber elbow

P. Induced draft blower

Q. Electrical connection inlets (alternate)

R. Coil front cover pressure tap
S. Coil front cover drain port

T. Drain line penetrations

U. Drain trap

V. Blower door interlock switch

W. Capacitor

X. 24-volt thermostat connections

Y. Integrated control module (with

fuse and diagnostic LED)

Z. Transformer (40VA)

AA. Circulator blower
AB. Auxiliary limit switch

AC. Junction box
AD. Electrical connection inlets

AE. Coil front cover

AF. Combustion air inlet pipe

Blower Compartment

Burner Compartment

I J

DEHU

T FOR

Blower Compartment

Burner Compartment

Counterflow/Horizontal

Upflow/Horizontal

■

Schools

■

Office buildings

■

Churches

■

Retail stores

■

Nursing homes

■

Hotels/motels

■

Common areas

■

Office areas

Содержание Gold WFD193





















































Результаты поиска

Содержание Gold WFD193

Отзывы:

Похожие инструкции для Gold WFD193

Бренды по названию

Популярные бренды

Whirlpool Gold WFD193, Руководство по установке

Результаты поиска

Содержание Gold WFD193

Отзывы:

Похожие инструкции для Gold WFD193

Бренды по названию

Популярные бренды