Whirlpool Gold WFD193 Скачать руководство пользователя

Страница: 45 / 52

■

No furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
6 flashes.

6 flashes

■

Rollout limit
switch open.

■

Integrated
control module
fuse is blown.

■

Flame rollout.

■

Misaligned burners,
blocked flue and/or air
inlet pipe or failed
induced draft blower.

■

Loose or improperly
connected wiring.

■

Short in 24-volt AC
control circuits or safety
circuits.

■

Faulty rollout limit
switch.

■

Check burners for
proper alignment.

■

Check flue and air inlet
piping for blockage,
proper length, elbows
and termination.
Correct as necessary.

■

Check rollout limit
switch. Replace if
necessary.

■

Check induced draft
blower for proper
performance. Replace
if necessary.

■

Tighten or correct
wiring connection.

■

Repair short in 24-volt
AC control/safety
circuit(s).

■

Replace integrated
control module fuse
(3A).

■

Turn off power
prior to repair.

■

Replace induced
draft blower with
correct
replacement part.

■

Replace
integrated control
module fuse with
3A automotive
fuse.

■

Read precautions
in “Electrostatic
Discharge (ESD)
Precautions”
section of
manual.

■

Replace rollout
limit switch with
correct
replacement part.

■

See “Vent/Flue
Pipe” section for
piping details.

■

Normal furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
7 flashes.

7 flashes

■

Flame sense
microamp signal
is low.

■

Flame sensor is coated/
oxidized.

■

Flame sensor incorrectly
positioned in burner
flame.

■

Lazy burner flame due to
improper gas pressure
or combustion air.

■

Sand flame sensor if
coated/oxidized.

■

Inspect for proper
sensor alignment.

■

Compare current gas
pressure to rating plate
info. Adjust as needed.

■

Turn off power
prior to repair.

■

Sand flame
sensor with
emery cloth.

■

See “Vent/Flue
Pipe” section for
piping details.

■

See rating plate
for proper gas
pressure.

■

No furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
8 flashes.

8 flashes

■

Problem with
igniter circuit.

■

Improperly connected
igniter.

■

Bad igniter.

■

Poor unit ground.

■

Poor burner ground.

■

Faulty integrated control
module.

■

Check and correct
wiring from integrated
control module to
igniter.

■

Replace bad igniter.

■

Check and correct
furnace ground wiring.

■

Replace faulty
integrated control
module.

■

Turn off power
prior to repair.

■

Replace igniter
with correct
replacement part.

■

Replace
integrated control
module with
correct
replacement part.

■

Read precautions
in “Electrostatic
Discharge (ESD)
Precautions”
section of
manual.

■

Induced draft
blower runs
continuously.
No furnace
operation.

■

Integrated
control module
diagnostic LED
is flashing
continuously.

Continuous

flashes

■

Polarity of
115-volt or
24-volt power is
reversed.

■

Polarity of 115-volt AC
power to furnace or
integrated control
module is reversed.

■

Red and blue wires to
transformer are
reversed.

■

Poor unit ground.

■

Review wiring diagram
to correct polarity.

■

Verify proper ground.
Correct if necessary.

■

Reverse red and blue
wires connected to
transformer.

■

Turn off power
prior to repair.

Symptoms of
Abnormal
Operation

Associated
LED Code

Fault Description Possible Causes

Corrective Actions

Notes and
Cautions

Содержание Gold WFD193





















































Результаты поиска

Содержание Gold WFD193

Отзывы:

Похожие инструкции для Gold WFD193

Бренды по названию

Популярные бренды

Whirlpool Gold WFD193, Руководство по установке

Результаты поиска

Содержание Gold WFD193

Отзывы:

Похожие инструкции для Gold WFD193

Бренды по названию

Популярные бренды