Whirlpool Gold WFD193 Скачать руководство пользователя | Manualshive

Страница: 16 / 52

background image

16

Combustion Air Pipe—Nondirect Vent Installations

A minimum of one 90° elbow should be installed on the
combustion air intake coupling to guard against inadvertent
blockage.

Standard Connection—Upflow

Standard Connection—Counterflow

Alternate Furnace Connections

If the standard locations are undesirable for a specific installation,
alternate side panel locations are available for both combustion
air inlet and vent/flue pipe connections. These locations may be
of particular benefit to upright upflow installations requiring
additional access to an A coil, or to upright counterflow
installations requiring additional access to a filter or electronic air
cleaner, or to horizontal installations desiring vent/flue (and
combustion air intake) piping run vertically from the side of the
cabinet.

NOTE: Standard and alternate locations can be combined (for
example, an installation may use the standard combustion air
intake location but use the alternate vent/flue location or vice
versa), if needed.

Alternate Vent/Flue Location

The alternate vent/flue location is the large hole directly in line
with the induced draft blower outlet. To use the alternate vent/flue
location, refer to the following steps and the “Alternate Vent/Flue
Location” illustration.

NOTE: Counterflow instructions follow the upflow instructions.

Upflow Units

1. Remove and save the 4 screws securing the vent/flue

coupling to the furnace top panel.

Counterflow Units

Remove and save the 4 screws securing the vent/flue
coupling to the furnace base pan. Also remove the 3 screws
securing the furnace’s internal vent/flue piping to the blower
deck.

Upflow and Counterflow Units

2. Loosen the worm gear hose clamps on the rubber elbow and

detach the rubber elbow from both the induced draft blower
and the vent/flue pipe.

3. Remove the vent/flue pipe from the furnace.

Upflow Units

4. Cut the vent/flue pipe 3

³⁄₄

" (9.5 cm) from the flanged end of

the pipe. See “Vent/Flue Pipe Cuts” illustration.

NOTE: The section of pipe attached to the coupling will reach
through the side panel to the induced draft blower.

5. Discard remaining pipe and elbows.

Counterflow Units

Cut the vent/flue pipe 3

³⁄₄

" (9.5 cm) from the blower deck

coupling. See “Vent/Flue Pipe Cuts” illustration

Save vent/flue pipe attached to the blower deck coupling for
use in the alternate location.

Discard remaining pipe and elbows.

A. 90º PVC elbow (nondirect vent only)
B. Combustion air pipe (direct

vent only)

C. Rubber coupling with worm

gear hose clamps

D. Vent/flue pipe

A. 90º PVC elbow (nondirect

vent only)

B. Combustion air pipe (direct

vent only)

C. Rubber couplings with worm

gear hose clamps

D. Vent/flue pipe

B

C

D

A

B

C

D

A

Goodman 56

Edges of sheet metal holes may be sharp. Use gloves as
a precaution when removing hole plugs.

WARNING

«
...
14
15
16
17
18
...
»

Содержание Gold WFD193





















































Отзывы:

Нет отзывов

Похожие инструкции для Gold WFD193

Бренд: ICP Страницы: 16

Бренд: A-Maize-Ing Heat Страницы: 46

Бренд: Goodman Страницы: 12

Hot Blast HB1520

Бренд: United States Stove Company Страницы: 52

GAS-FIRED UPFLOW FURNACE 394U

Бренд: Bryant Страницы: 4

Бренд: Fire Chief Страницы: 30

Бренд: ICP Страницы: 36

Бренд: Windhager Страницы: 40

Бренд: ICP Страницы: 2

Бренд: RANSOM & RANDOLPH Страницы: 17

Бренд: Winchester Страницы: 16

Бренд: Winchester Страницы: 19

Бренд: Ferroli Страницы: 64

Бренд: Empire Comfort Systems Страницы: 10

Бренд: Empire Comfort Systems Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды