Whirlpool DP840DWG страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 66

background image

55

Removing Access and Door Panels

1. Loosen but do not remove the two (2) toe

panel screws below the access panel. Re-
move and set aside the two (2) screws above
the access panel.

(Fig. 4-1)

2. Remove the access panel assembly by slid-

ing it upward to clear the loosened screws.
This access panel will be replaced by new a
new custom panel assembly.

(Fig. 4-1)

3. Remove the two (2) screws from the bottom

of the outer door panel.

(Fig. 4-1)

Section Four

INSTALLATION CONSIDERATIONS

INSTALLING CUSTOM PANEL ACCESSORY KIT

Installation Instructions

In many instances, customers want to integrate the undercounter dishwasher appearance with overall
kitchen design by installing panels of wood matching that used in the cabinets. After the two panels -
an upper panel and a lower panel - are cut and finished as described below, use the materials in the
Dishwasher Custom Panel Accessory Kit to install them by following the installation instructions.

Custom Panel Dimensions

NOTE: A ¼” thickness (actual 7/32”) can be used
for wood panels. If using thicker material, edges
must be routed to 7/32” as shown in box below.

7/32"

Max.

1" Min.

Required on

top and bottom

edges

18-21/32"

22-13/16"

Upper

panel

Lower

panel

45

Min.

ø

45

Min.

ø

7/32" Max.

1/4"

Min.

1/4"

Min.

4-7/16"

23-5/16"

(Fig. 4-1)

CUTTING NOTES:

1.

Custom panel for the door cannot exceed 8 lbs. weight.

2.

The upper and lower panels are not the same width.

3.

Match wood grain direction with that of adjacent cabi
znets.

4.

Sand panel edges to provide smooth finish.

5.

IMPORTANT: Use moisture resistant sealer on both sides
and all edges of the panels to protect from humidity. Dish
washer is subject to humidity.

Custom Color Panels:

Black

P/N 675775

White

P/N 675776

Almond

P/N 675777

«
...
57
58
59
60
61
...
»

Содержание DP840DWG



































































Отзывы:

Нет отзывов

Похожие инструкции для DP840DWG

WF501ANW Trouble Shooting Guide

Бренд: Samsung Страницы: 132

Бренд: P&C Страницы: 72

Бренд: Saba Страницы: 39

Бренд: Silverline Страницы: 88

FAVORIT 88015 VI

Бренд: AEG Electrolux Страницы: 36

Бренд: Bush Страницы: 25

Executive Elite

Бренд: IFB Страницы: 31

Бренд: Washtech Страницы: 12

Бренд: Daewoo Страницы: 57

Бренд: Samsung Страницы: 110

WW80H5440E Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 136

WW80H5400E Series

Бренд: Samsung Страницы: 88

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды