Whirlpool DP840DWG Скачать руководство пользователя

Страница: 54 / 66

PROBLEM

POSSIBLE CAUSES

CORRECTION/TEST

Dishwasher does not run or
stops during a cycle

Dishwasher will not fill

Dishwasher will not drain

Dishwasher will not
dry dishes

Door is not latching properly.

Child lock is "ON".

Wash Cycle not set properly.

Household fuse blown or circuit
breaker tripped.

Washer is not wired into a circuit with
proper voltage.

Overflow protection float is stuck in
"up" position.

Fill valve is inoperable.

Control board is inoperable.

Air gap (if installed) is clogged.

Pump motor is inoperable

Control board is inoperable.

Heater element burned out.

Hi-limit thermostat inoperable.

Check to make sure handle link
is properly seated in door latch
assembly. Check that the door
switch is opening and closing
properly.

Turn child lock "OFF"

Review setting Wash Cycles in
the Use and Care Guide.

Have a qualified electrician check
the circuit breaker or fuse.

Have customer call a qualified
electrician.

Check that the overflow
protection float is free to move
"up" and "down". Check that the
overfill switch in opening and
closing properly.

Check for continuity between
contacts on fill valve.

Check for 110VAC between P2-5
and P12-3.

Follow air gap manufacturer's
direction for cleaning.

Disconnect pump motor from
wiring harness and check for
continuity between V & BU, V &
GY and V & Y.

Check for 110VAC between P10
and P3, P10 and P5 and P10
and P4.

Check for continuity between the
terminals of the heater element.
Check for 110VAC between P6
and P8.

Check for continuity between
terminals of the hi-limit
thermostat.

PRECAUTIONS TO BE OBSERVED WHILE TROUBLESHOOTING

AND DIAGNOSING PROBLEMS

Always check wiring harness and connectors before initiating any test procedures.

Disconnect electric power from the dishwasher before touching the printed circuit boards or re-seating wire connectors.

Voltage checks should be made by inserting meter probes beside the wires in the connector blocks with the electric power source on
and the connector block plugged in.

Resistance checks should be made on components with the electric power off and the connector blocks disconnected.

TROUBLESHOOTING GUIDE

Содержание DP840DWG



































































Результаты поиска

Содержание DP840DWG

Отзывы:

Похожие инструкции для DP840DWG

Бренды по названию

Популярные бренды

Whirlpool DP840DWG, Руководство пользователя

Результаты поиска

Содержание DP840DWG

Отзывы:

Похожие инструкции для DP840DWG

Бренды по названию

Популярные бренды