Whirlpool DP840DWG страница 12 Скачать руководство пользователя

Страница: 12 / 66

1. Disconnect the dishwasher from the electrical

supply and remove the toe panel and access
panel from the bottom of the dishwasher.

2. Disconnect the end of the door springs

from the door spring tension adjustment
holes in the frame runner. Note which
holes were used and reattach the door
springs in the same holes when the repairs
are complete.

(Fig. 1-21)

3. Open the dishwasher door and remove the

eight (8) T-15 Torx screws securing the inner
door panel from the door frame.

(Fig. 1-22)

4. Remove the timer cover by releasing the

two (2) retaining tabs at each end from the
door frame.

Removing the Check Valve

1. Remove the toe panel and access panel from the

bottom of the dishwasher.

2. Remove the hoses from the check valve.

3. Remove the Hex-head screw securing the check valve to

the tub support.

(Fig. 1-19)

RETAINING

SCREW

Fig. 1-19

Removing the Motor Relay

1. Disconnect the dishwasher from the electrical supply and remove

the toe panel and access panel from the bottom of the dishwasher.

2. Disconnect the three (3) wiring harness connectors from the motor relay terminals.

3. Remove the Hex-head screw securing the motor relay to the tub support.

(Fig. 1-20)

Fig. 1-20

RETAINING

SCREW

Accessing Components Inside the Door

Fig. 1-21

T-15

TORX

Fig. 1-22

Содержание DP840DWG



































































Результаты поиска

Содержание DP840DWG

Отзывы:

Похожие инструкции для DP840DWG

Бренды по названию

Популярные бренды

Whirlpool DP840DWG, Руководство пользователя

Результаты поиска

Содержание DP840DWG

Отзывы:

Похожие инструкции для DP840DWG

Бренды по названию

Популярные бренды