background image

GB12

After unpacking the appliance, check for any transport damage. In the event of problems, contact the dealer or your nearest After-sales Service. To prevent any
damage, only remove the appliance from its polystyrene foam packaging at the time of installation.

PREPARING FOR INSTALLATION

this is a heavy product; the hood should only be lifted and installed by two or more people.

The minimum distance between the cooking pans on top of the cooker and the bottom of the hood must not be less than 50 cm for electric cookers and 65 cm
for gas or mixed cookers.
Before installation also check the minimum distances stated in the manual of the cooker.

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance rating plate is the same as the mains voltage.
This information may be found on the inside of the hood, under the grease filter.
Power cable replacement (type H05 RR-F 3 x 1.5 mm) must be carried out by a qualified electrician. Contact an authorized service centre.
If the hood is fitted with an electric plug, connect the plug to a socket complying with current regulations, located in an accessible place. If no plug is fitted
(direct wiring to the mains), or if the socket is not located in an accessible place, install a standardised double pole power switch that will enable complete
isolation from the mains in case of category III overvoltage conditions, in accordance with installation rules.

GENERAL RECOMMENDATIONS
Before use

Remove cardboard protection pieces, protective film and adhesive labels from accessories.
Check the appliance for any transport damage.

During use

To avoid any damage do not place any weights on the appliance.
Do not expose the appliance to atmospheric agents.

WARNING:

Disposal of packing

The packing material is 100% recyclable and is marked with the recycle symbol (

). The various parts of the packing must therefore be disposed of

responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product

-

This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).

-

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which
could otherwise be caused by inappropriate waste handling of this product.

-

The symbol 

on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an

appropriate collection centre for the recycling of electrical and electronic equipment.

INSTALLATION

SAFEGUARDING THE ENVIRONMENT

Содержание 809











Отзывы: