Whirlpool 400011239758, Инструкция по эксплуатации, Страница: 21 / 36

21
EN
c off ee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
Tips for a hott er coff ee
For hotter c off ee, you should:
• perform a rinse cycle by selecting the "Rinsing" function in
the settings menu (section “Rinsing ”);
• warm the cups with hot water using the hot water function
(see section “Delivering hot water”);
• increase the c off ee temperature in the settings menu (see
section “C off ee temperature ”).
MAKING CAPPUCCINOS AND MILK-BASED COFFEES
To avoid milk with poor froth or large bubbles, always clean the
milk container lid (D2) and hot water connection nozzle (A10)
as described in sections “Cleaning the milk container after use”,
“Cleaning the milk container” and “Cleaning the hot water/
steam connection nozzle”.
Filling and attaching the milk container
1. Remov e the lid (D2) (fi g. 15);
2. Fill the milk container (D3) with a suffi cient quantity of
milk, not exceeding the MAX level marked on the contain-
er
(fi g. 16). Each mark on the side of the container corre-
sponds to about 100 ml of milk;
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
• If "Energy Saving" mode is enabled, you may have to wait a
few seconds before the beverage is delivered.
1. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk con tainer lid (fi g. 17);
2. Place the lid back on the milk container;
3. Remove the hot water/steam spout (
C4) (fi g. 18);
4. Attach the milk container (D) to the connection nozzle
(A10) and push as far as it will go (fi g. 19). The machine
emits a beep (if the beep function is enabled);
5. Place a suffi ciently large cup under the c off ee spouts (A13)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fi g. 20).
5. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial (D1) on the milk container lid to
adjust the amount of froth on the milk delivered while making
milk-based c
off ees. Follow the tips in the table below:
Dial
position
Description Recommended for
No froth CAFFELATTE /
HOT MILK
Min. froth LATTE MACCHIATO
Max. froth CAPPUCCINO /
MILK (frothed milk)
Making cappuccinos and milk-based coff ees auto-
matically
1. Fill the milk container (D) and attach it as described above.
2. Select the required beverage from the homepage:
•
CAPPUCCINO
• LATTE MACCHIATO
• CAFFELATTE
• HOT MILK
• CAP
• ESPRESSO MACCHIATO
• FLAT WHITE
• CAPPUCCINO MIX
3. A message on the display (B) instructs you to turn the froth
adjustment dial (D1) according to the froth required by the
original recipe. Turn the dial on the milk container lid (D2)
and c
onfi rm the selection by pressing .
4. After a few seconds, preparation begins automatically and
an image of the selected beverage appears on the display,
together with a progress bar which gradually
fi lls as prepa-
ration progresses.
General indications when preparing all milk based drinks
•
: press to interrupt preparation completely and go
back to the homepage.
• : press to interrupt milk or c off ee delivery and
move on to the next delivery (if applicable) to complete the
beverage.
• At the end of delivery, to increase the quantity of c off ee in
the cup, press .
• Preparation of each c off ee can be customised (see sections
“Customising the beverages” and “Memorising your per-
sonal pr
ofi le”).
• Do not leave the milk container out of the refrigerator for
long periods. The warmer the milk (5°C is ideal), the poorer
the quality of froth produced.
Once the c off ee has been made, the appliance is ready to make
the next beverage.