Woodway Engineering Ltd
Lower Road, Barnacle
Coventry, CV7 9LD
United Kingdom
Tel: +44 (0) 24 76 841750
Fax: +44 (0) 24 76 621796
www.woodwayengineering.com
I N S T A L L A T I O N G U I D E
10
Woodway Engineering Ltd
Lower Road, Barnacle
Coventry, CV7 9LD
United Kingdom
Tel: +44 (0) 24 76 841750
Fax: +44 (0) 24 76 621796
www.woodwayengineering.com
I N S T A L L A T I O N G U I D E
10
Mount the lightbar to the roof of the vehicle following the steps in the supplied lightbar installation guide.
The CenCom Sapphire
™ UK is focused towards that use of any lightbar from the WeCan
®
range.
WeCan® Connection
Run the green (CAN high) and grey (CAN low) WeCan®
wires to the CenCom Sapphire
™ UK using the supplied 3
way WeCan
® screw terminal plug supplied. Using ferrule
crimps screw the wires into the 3 way plug using the
following connections:
Pin 1 = Green CAN high
Pin 2 = Shield
Pin3 = Grey CAN low
www.woodwayengineering.com - +44 (0) 2476 841750
Lower Road, Barnacle, Coventry, United Kingdom, CV7 9LD
SAPPHIRE UK
CENCOM - Quick Start Guide V6.1 - 22 March 2016
1
2
3
4
4
3
2
1
1 2 3 4 5 6 7 8
10 7 4
3
12 9 6 3
2 1
6 5 4
1 2 3
1
1
7
8
14
Mount the lightbar to the roof of the vehicle following the steps in the supplied lightbar
Installation Guide.
The CenCom Sapphire™ UK is focused towards the use of any lightbar from the WeCAN™
range.
To wire the lightbar to the CenCom Sapphire™ UK, connect the lightbars attached Red power
wire to the battery’s ‘Positive’ (+) terminal and the Black power wire to ‘Ground’ (-). Ensure that
you install a fuse and that the correct rating for your fitted lightbar (see lightbar Installation
instructions if unsure), is fitted in line with your
Red
power wire as close to the battery terminal
as possible. If wires need to be extended, ensure that the wire used is correctly rated for the
necessary current (recommended 125% of maximum current draw).
Run the
Green
(CAN High) and
Grey
(CAN Low) WeCan® wires to the CenCom Sapphire™
UK Using the supplied 3 Way WeCan® screw terminal plug supplied. Using Ferrule crimps
screw the wires into the 3 Way Plug using the following connections:
Pin 1 =
GREEN
CAN High
Pin 2 =
SHIELD
Pin 3 =
GREY
CAN Low
With the three wires securely fastened into the 3 Way plug, it can then be connected to plug J
of the CenCom Sapphire™ UK by firmly mating the two connectors together.
The lightbar flash patterns can now be programmed using the supplied CenCom Sapphire™
UK programming software.
WeCan® Connection
To wire the lightbar to the CenCom Sapphire™ UK, connect the lightbar attached red power wire to the battery’s ‘positive’
(+) terminal and black power wire to ‘ground’ (-). ensure that you install a fuse and that the correct rating for your fitted
lightbar (see lightbar installation instructions if unsure), is fitted in line with your red red power wire as close to the battery
terminal as possible. IF wires need to be extended, ensure that the wire used is correctly rated for the necessary current
(recommended 125% of maximum current draw).
With the three wires securely fastened into the 3 way plug, it can then be connected to plug J of the CenCom Sapphire™
UK by firmly mating the two connectors together.
The lightbar flash patterns can now be programmed using the supplied CenCom Sapphire™ UK programming software.
