Page 4
Control Cable Operation / HC:
Warning Light Functions:
GRN: Front Corners (Fuse wire @ 5 AMPS)
ApVBAT to the GRN wire activates the Front Corners.
GRN/WHT: Front Directionals (Fuse wire @ 15 AMPS)
ApVBAT to the GRN/WHT wire activates the Front Directionals.
BLUE: Rear Corners (Fuse wire @ 5 AMPS)
ApVBAT to the BLUE wire activates the Rear Corners.
BLU/WHT
:
Rear Directionals (Fuse wire @ 15 AMPS)
ApVBAT to the BLU/WHT wire activates the Rear Directionals.
VIOLET: Low Power (Fuse wire @ 1 AMP)
ORANGE
:
Pattern Override (Fuse wire @ 1 AMPS)
ApVBAT to the ORANGE wire while lightheads are activated, will
change the flash pattern to whatever pattern override is programmed for.
To program the flash pattern activate the lightbar then activate pattern
override by applying +VBAT to the ORANGE wire and select a flash
pattern using Scan-Lock™.
VIOLET: Low Power (Fuse wire @ 1 AMP)
The type of switch used is dependent on how the operator wishes the Hi/
Low feature to function:
Latching Mode:
By apVBAT to the VIOLET wire for less than 1
sec., the power supply is “latched” into low power operation. The unit must
be turned off and then back on to restore normal, Hi power operation.
(Momentary Switch)
Level Mode:
ApVBAT to the VIOLET wire for over 1 sec. holds the
power supply in low power mode until voltage is removed. (Toggle Switch)
Wht/Vio: Scan-Lock™ (Fuse wire @ 1 AMP)
To change the flash pattern on any light, activate only that light.
TO CHANGE PATTERNS:
To cycle forward to the next available pattern
apply +VBAT to the WHITE-VIOLET wire for less than 1 second and
release.
To cycle back to the previous pattern apply
+VBAT to the WHITE-
VIOLET wire for more than 1 second and release.
TO CHANGE THE DEFAULT PATTERN:
When the desired pattern is
displayed, allow it to run for more than 5 seconds. The light will now
display this pattern when initially activated.
TO RESTORE THE FACTORY DEFAULT PATTERN:
Turn power to the
light off. While apVBAT to the WHITE-VIOLET wire, turn power to
the light on. The factory default pattern is now displayed.
Use a Normally Open Momentary Switch for Scan-Lock™ operation.
Scan-Lock is also used to select from four cruise light intensities.
BLK:
Ground 1 (Warning Light) - Extend to ground.
BLK/WHT:
Ground 2 (Warning Light) - Extend to ground.
External ION™ Pods:
RED:
Apply +12VDC to this wire to activate the Front ION Pod. (Fuse @ 3
AMPS)
GRN:
Apply+12VDC to this wire to activate the Rear ION Pod.
(Fuse @ 3
AMPS)
BLK:
Front ION Pod ground wire.
Extend to ground
.
WHT:
Rear ION Pod ground wire.
Extend to ground
.
Optional Take-Down/Alley Functions:
WHT
:
Driver Alley (Fuse wire @ 3 AMPS)
Applying +VBAT to the WHITE wire will activate the Driver Side Alley
Light.
YEL
:
Passenger Alley (Fuse wire @ 3 AMPS)
Applying +VBAT to the YELLOW wire will activate the Passenger Side
Alley Light.
WHT/BLK
:
TakeDowns (Fuse wire @ 3 AMPS)
ApVBAT to the BLK/WHT wire will activate the TakeDowns
WHT/BLU
:
Driver Alley (Fuse wire @ 3 AMPS)
Applying +VBAT to the WHT/BLU wire will activate the Flashing
TakeDowns.
BLK:
Ground (Alley Light) - Extend to ground.
BLK/WHT:
Ground (Take-Down) -
Extend to ground.
RED - POS (+) FRONT ION LIGHTHEADS
SPEAKER (+) POSITIVE
WHT - NEG (-) REAR ION LIGHTHEADS
GRN - POS (+) REAR ION LIGHTHEADS
SPEAKER (-) GROUND
Extend both speaker
wires to your control
box.
+
Battery
-
GRN/WHT -
Front Directionals
WHT -
Driver Alley
GRN -
Front Corners
YEL -
Passenger Alley
5 AMP
15 AMP
15 AMP
5 AMP
3 AMP
3 AMP
3 AMP
3 AMP
1 AMP
1 AMP
1 AMP
BLU -
Rear Corners
WHT/BLK -
Take-Down
WHT/BLU -
Flashing T-D
BLK - NEG (- FRONT ION LIGHTHEADS
BLK/WHT -
Ground (Take-Down)
BLU/WHT -
Rear Directionals
BLK -
Ground (Alley)
VIO -
Low Power
ORG -
Pattern Override
WHT/VIO -
ScanLock
BLK -
Ground 1 (Warning Light)
BLK/WHT -
Ground 2 (Warning Light)
Warning Lights
Takedown-Alley Option
External Pods
= Switch (SP/ST)
= Fuse
= Switch (Mom. N.O.)
Fuse both wires @ 3 AMPS
