Page 3
Routing the Lightbar Cable(s):
1.
To protect the headliner from damage caused by drilling the cable
access hole through the vehicle roof, allow a 5” to 7” distance
between roof and headliner by lowering the headliner before drilling.
2.
Using a 1” hole saw, drill the cable access hole then use a round file
to smooth and de-burr the edges of the hole. Install a 1” grommet
(user supplied).
NOTE: There may be a roof support member that spans the distance
between the driver’s and passenger’s side. DO NOT DRILL
THROUGH THIS MEMBER! Adjust the location until the hole can be
drilled without contacting this support member.
3.
Insert the cable(s) through the cable access hole into the vehicle.
Use RTV silicone to weatherproof the access hole after the cable(s)
are pulled completely into the vehicle.
4.
Route the cable(s) one at a time to their respective destinations
(power cable to vehicle battery; control cable to switch panel). Refer
to the instructions included with your switches for switch wiring
information.
Permanent Mounting:
Caution:
Permanent mounting of this product will require drilling.
It is absolutely necessary to make sure that no other vehicle
components could be damaged by this process. Check both sides of
the mounting surface before starting. If damage is likely, select a
different mounting location.
1.
Install the mounting foot to the lightbar following steps 1 thru 4 of
“Strap Mounting”.
2.
Drill two holes in each mounting foot as shown to accommodate the
permanent mount hardware.
3.
Position the lightbar
onto the vehicle in its
exact
mounting
location and mark the
location
of
the
mounting holes onto
the surface of the roof
using the mounting
feet as templates.
4.
Remove the lightbar
and
drill
the
4
mounting holes.
5.
Install
the
lightbar
using the supplied 1/4
- 20 Socket Head
Machine Screw, 1/4”
Internal Tooth Lock
Washer and 1/4 - 20 X
7/16 Hex Nut.
Available Flash Patterns:
1.
SignalAlert™ - L/R SYNC
2.
SignalAlert™ - L/R ASYNC
3.
SignalAlert™ - IN/OUT
4.
SignalAlert™ - SIM
5.
SignalAlert™ - ALT/SIM
6.
CometFlash® - L/R SYNC
7.
CometFlash® - L/R ASYNC
8.
CometFlash® - IN/OUT
9.
CometFlash® - SIM
10.
CometFlash® - ALT/SIM
11.
DoubleFlash 75 - L/R SYNC
12.
DoubleFlash 75 - L/R ASYNC
13.
DoubleFlash 75 - IN/OUT
14.
DoubleFlash 75 - SIM
15.
DoubleFlash 75 - ALT/SIM
16.
SignalFlash 75 - L/R SYNC
17.
SignalFlash 75 - L/R ASYNC
18.
SignalFlash 75 - IN/OUT
19.
SignalFlash 75 - SIM
20.
SignalFlash 75 - ALT/SIM
21.
LongBurst™ - L/R SYNC
22.
LongBurst™ - L/R ASYNC
23.
LongBurst™ - IN/OUT
24.
LongBurst™ - SIM
25.
LongBurst™ - ALT/SIM
26.
SingleFlash 60 - L/R SYNC
27.
SingleFlash 60 - L/R ASYNC
28.
SingleFlash 60 - IN/OUT
29.
SingleFlash 60 - SIM
30.
SingleFlash 60 - ALT/SIM
31.
SingleFlash 90 - L/R SYNC
32.
SingleFlash 90 - L/R ASYNC
33.
SingleFlash 90 - IN/OUT
34.
SingleFlash 90 - SIM
35.
SingleFlash 90 - ALT/SIM
36.
SingleFlash 120 - L/R SYNC
37.
SingleFlash 120 - L/R ASYNC
38.
SingleFlash 120 - IN/OUT
39.
SingleFlash 120 - SIM
40.
SingleFlash 120 - ALT/SIM
41.
SingleFlash 240 - L/R SYNC
42.
SingleFlash 240 - L/R ASYNC
43.
SingleFlash 240 - IN/OUT
44.
SingleFlash 240 - SIM
45.
SingleFlash 240 - ALT/SIM
46.
ActionFlash™ - L/R SYNC
47.
ActionFlash™ - L/R ASYNC
48.
ActionFlash™ - IN/OUT
49.
ActionFlash™ - SIM
50.
Ping-Pong™ - L/R SYNC
51.
Ping-Pong™ - L/R ASYNC
52.
Ping-Pong™ - IN/OUT
53.
Ping-Pong™ ™- SIM
54.
ModuFlash™ - L/R SYNC
55.
ModuFlash™ - L/R ASYNC
56.
ModuFlash™ - IN/OUT
57.
ModuFlash™ - SIM
58.
DoubleFlash 125
59.
SingleFlash 125
L/R SYNC
=
Left / Right Synchronous
L/R ASYNC
=
Left / Right ASynchronous
SIM =
Simultaneous
IN/OUT =
In / Out
ALT/SIM =
Alternating-Simultaneous
Measure Distance on lightbar being mounted
11.038”
1/4 - 20 X 2-1/2"
PHILLIPS PAN HEAD
MACHINE SCREW
1/4 - 20 X 2-1/2"
PHILLIPS PAN HEAD
MACHINE SCREW
1/4 - 20 X 2-1/2"
PHILLIPS PAN HEAD
MACHINE SCREW
1/4 - 20 X 7/16
HEX NUT
1/4" INTERNAL
TOOTH LOCK
WASHER
Permanent Mountng
Permanent Mounting
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle components/equipment.
FRONT OF LIGHTBAR
Drilling the Cable Access Hole
For Driver-side cable
For Passenger-side cable