background image

Page 3

READ BEFORE INSTALLING!!!

Do not install this product or route any wires in the deployment
area of your air bag. Equipment mounted or located in
the air bag deployment area will damage or reduce the
effectiveness of the air bag or become a projectile that could
cause serious personal injury or death. Refer to your vehicle
owner's manual for the air bag deployment area.

The User/Installer assumes full responsibility to determine the
proper mounting location, based on providing ultimate safety
to all passengers inside the vehicle. Whelen Engineering Co.
assumes no liability or responsibility for determining individual
applications or exact installation location criteria.

5.875"

5-7/8"

2.65"

2-21/32"

2.938"

2-15/16"

2.50" 2-1/2"

Mounting
Screws
(Qty. 4)

CUT-OUT THIS AREA

CUT-OUT THIS AREA

CUT-OUT THIS AREA

1.25" 1-1/4"

5.00”

5"

2.50"

2-1/2"

1.325"

1-21/64

SIDE VIEW

2.375"

2-3/8"

2.95"

2-61/64"

R

The 295HFS2, although technologically advanced, is simple to
install.  the  295HFS2  is  specially  designed  for  dash  (or  panel)
mounting. 

WARNING:

  Mounting  will  require  drilling.  It  is

absolutely necessary to make sure that no vehicle components
behind  the  mounting  area  will  be  damaged.  If  damage  is
possible, select another location.

NOTE:

 Before starting read all warnings on next page.

Installation: Control Head

The  flush  mount  unit  can  be  mounted  in  a  console,  dash  or
other suitable location. Using the measurements below, cut-out
the hole for the control head, then slide the unit in and drill the 4
holes for the customer supplied mounting hardware.

IMPORTANT:

  Template  is  not  to  scale.  Check  measurements

before  drilling.  Measurements  are  given  in  decimals  and
fractions  for  your  convenience.  For  a  more  accurate
measurement and installation you 

should

 use the decimals.

Installation: Amplifier

1.

From  inside  the  trunk,  position  the  amplifier  against  the
vertical trunk wall behind the rear seat and mark off the 4
mounting  holes  using  a  scribe  or  other  suitable  tool.  Be
sure  that  the  remote  amplifier  fits  properly  and  does  not
interfere with any parts of the trunk or seat back.

2.

Carefully  drill  the  indicated  holes  using  an  appropriately
sized drill bit, then, using the supplied sheet metal screws,
secure the remote amplifier to the vertical trunk wall.

Содержание 295HFS2 Series








Отзывы: