Page 3
PCB ASSEMBLY (COMPONENT SIDE)
Refer to diagram on page 2 to dismantle strobe
JU1
BLACK
JU2
RED
JU6
If you wish
to control
Hi/Low Power
externally, cut the VIOLET wire off at this
point and exit with the BLACK and RED
wires. Ground this wire to go to high
power. You may install an SPST switch
(customer supplied).
To achieve any of the 4 flash patterns,
you must either cut-out or leave-in one,
two, both or neither of the two jumpers. If
you do not touch the jumpers the beacon
will default to QuintFlash.
Q u i n t F l a s h
D o u b l e F l a s h
R a p i d R a n d o m
A c t i o n F l a s h ™
JU1
JU2
IN
IN
CUT
CUT
IN
CUT
IN
CUT
FLASH PATTERNS
FLASH PATTERN SELECTION
HI/LOW
POWER
CONTROL
1
0 1 - 0 6 8 3 3 4 0 _ _ _
DOME
COLOR
BASE
PART
NUMBER
KEY
DOME:
COLOR:
BASE:
H
= HIGH DOME
L
= LOW DOME
A
= AMBER
B
C
G
R
V
= BLUE
= CLEAR
= GREEN
= RED
= VIOLET
P
= PERM MOUNT
M
= MAG MOUNT
DESCRIPTION
PCB ASSY MODEL 2015 & VP415 DIE CAST SERIES
BASE / DIE CAST / BLACK W/1" NPT
FLASH TUBE ASSY / FTU 10W
"O" RING
SEAL / BASE
3/8 GROMMET P/N 901132093
TO-3P CHO-THERM INSULATOR
SPRING CLIP / TRANSISTOR MOUNT
NUT, NO.6 FASTEX SCREW GROMMET
6-32 X 5/16 HEX WASHER HD THD FORMING
N0.4 X 1/2 PPHDSMS
6-32 X 1/2 PAN HD THD FORMING
MOUNTING COLLAR, BLACK
OPTIC DOME / AMBER / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / AMBER / HIGH PROFILE / 5-3/4“ HIGH
N0.8 X 1/2" PPHSMS
FINAL ASSY MODEL 2015 & VP415 DIE CAST SERIES
MAGNET MOUNT KIT
OPTIC DOME / BLUE / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / CLEAR / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / GREEN / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / RED / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / VIOLET / LOW PROFILE / 4-3/4“ HIGH
OPTIC DOME / BLUE / HIGH PROFILE / 5-3/4“ HIGH
OPTIC DOME / CLEAR / HIGH PROFILE / 5-3/4“ HIGH
OPTIC DOME / GREEN / HIGH PROFILE / 5-3/4“ HIGH
OPTIC DOME / RED / HIGH PROFILE / 5-3/4“ HIGH
OPTIC DOME / VIOLET / HIGH PROFILE / 5-3/4“ HIGH
PART NUMBER
02-0168667-00
06-180842-002
36-0341566-00
38-0441331-00
38-0240821-00
21-11091202-0
56-000000-100
23-0320760-00
13-062C40-16J
15-066939-056
15-041416-080
15-065419-080
11-760897-000
68-2180452-10
68-2180483-10
15-081416-080
01-0683340 - - -
01-0461585-00
68-2180452-20
68-2180452-30
68-2180452-40
68-2180452-50
68-2180452-V0
68-2180483-20
68-2180483-30
68-2180483-40
68-2180483-50
68-2180483-V0
1
2
3
4
5
6
7
8
9
11
12
13
14
17
18
19
20
21
ITEM
22
23
24
25
26
27
28
29
30
1
1
1
1
1
1
1
1
2
3
2
2
1
QTY
OPT
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
3
A/R
1
NOTE:
DC voltage models are polarity sensitive. If the positive and nega-
tive wires are reversed the unit will not function. The fuse is installed
between the power source and the strobe light beacon IN THE POSITIVE
(+) LINE (red wire) and must be fused at the battery.
MOUNTING INSTRUCTIONS:
This strobe beacon features a combination base which may be used for
either FLANGE MOUNT, 1 INCH (NPT) PIPE MOUNT, or PERMANENT
MOUNT. The threading for a 1 inch (NPT) pipe mounting is precast in the
cast aluminum base,
FLANGE MOUNT
1.
Select the mounting location taking into consideration visibility of the
strobe light flash, mounting surface and ease of wiring.
2.
Using the base gasket (ITEM 5) as a template, mark the 3 mounting
holes and center wire access hole onto mounting surface.
3.
Drill three mounting holes using a #29 drill (.136 inch, 3.5mm).
4.
Drill the wire access hole using a 3/8 inch drill (.375 inch, 9.5mm). Be
sure to remove burrs from access hole to prevent any damage to wires.
5.
Place gasket (ITEM 5) on mounting surface aligned with the
holes in the mounting surface. After connecting the beacon to the
power cable, feed wires through wire access hole. Place beacon
into proper position and slip mounting collar (ITEM 17) over
beacon to fit around the base of the unit. Align the 3 holes in the
mounting collar with the 3 mounting holes in the mounting
surface. Use the 3 enclosed mounting screws (ITEM 18) to
secure beacon to mounting surface.
1 INCH (NPT) PIPE MOUNT.
1.
Feed the power cable through the 1 inch pipe and connect the
cable to the wires of the Beacon.
2.
Screw the beacon to the threads on the 1 inch pipe, taking
precaution not to damage the connected power supply wires.
PERMANENT MOUNT
This mounting of the strobe beacon is a tamper-proof way to secure
the unit to the mounting surface. Mounting screws are hidden inside
the base, and aren’t accessible unless unit is dismantled.
1.
Remove the screws holding on the optic dome (ITEM 20) and
remove the dome. Then remove the screws holding on the power
supply (ITEM 1) and remove the power supply.
2.
Locate the four, .164 inch dimples within the perimeter of the cast
aluminum base. (See illustration below). Punch these dimples
out to create a hole for the mounting screws to fit through.
3.
Using the base as a template mark the 4 mounting holes onto the
mounting surface. Remove the base and mark in the center of
the 4 mounting holes, the location of the wire access hole.
4.
Drill the mounting holes into the mounting surface to fit customer
supplied mounting hardware, drill the wire access hole using a
3/8 inch drill (.375 inch, 9.5mm). Remove burrs from wire access
hole to prevent damage to wires. It is also recommended that you
install a rubber grommet in each wire hole to protect the wires.
5.
The gasket (ITEM 5) will be used between the base and the
mounting surface. Cut the gasket along the perforated circle to fit
diameter of base.
6.
After connecting beacon to power cable, feed the wires through
the cable access hole and place the base with the gasket on the
mounting surface, lining up the mounting holes in the base with
the ones in the mounting surface. Secure base firmly to mounting
surface with customers hardware and reassemble beacon.
DIMPLES
DIMPLES
TOP VIEW INSIDE BASE
SEE PG. 3
IMPORTANT
INFORMATION
ON BASE.
