12
INSTALLATION
13
OPERATING
Choosing utensils for gas hotplates
Refer to the diagram below�
(oversize)
(undersize)
Do not use utensils which are too large or too small�
Installation and service warning
WARNING
WARNING
•
Only an authorised person must install and service this
appliance (Certificate of Compliance to be retained)�
•
In order to avoid a hazard, the installation instructions
MUST be followed�
•
In order to avoid the appliance tipping, the anti-tilt plate
MUST be installed�
•
Appliances requiring connection to 230 – 240V
MUST be earthed�
•
An authorised person should inspect this appliance
every 5 years�
•
This appliance must NOT be installed on a base,
box or in a closed cupboard�
•
If the electrical supply cord is damaged, a qualified person
MUST replace the cord to avoid a hazard or
void your warranty�
WARNING
WARNING
Surrounding kitchen cabinets MUST WITHSTAND 85°C.
Before operating first time
1�
Read all the Warning and Safety information�
2�
Remove all internal boxes and bags from oven�
3�
Clean out the oven interior with detergent and warm
water and polish with a soft cloth� DO NOT close oven
door until the oven is completely dry�
Setting the time
4�
If you have purchased a model fitted with a 3 button
programmable timer, you must set the time of day before
you can operate your appliance�
•
After the appliance has been electrically connected '12�00'
will be displayed and the 'clock indicator' will flash�
•
To set the time of day, press the – or + buttons� 5 seconds
after the last change, the 'clock' indicator will disappear,
confirming the time has been set�
NOTE: The clock has a 24-hour display.
5�
New appliances can have an odour during first operation�
It is recommended to ‘run in’ the oven before you cook
Run the oven at 180°C for 30 minutes and ensure that
the room is well ventilated�
6�
For products with a separate grill compartment, run grill
on maximum for 15 minutes with grill door open�
7�
If your appliance is fitted with solid hotplates, turn heat
setting to high for 3 minutes to fully harden the
hotplate coating�
GOOD
BAD
(moisture on hotplate)
BAD
(convex base)
BAD
(oversize)
BAD
(recessed base)
BAD
(undersize)
BAD
(no utensil)
(recessed base)
(convex base)
(undersize)
(oversize)
(moisture on
hotplate)
(no utensil)
Choosing utensils for electric hotplates
Refer to the diagram below�
OPERATING FOR THE FIRST TIME
Checking the gas supply
1� Check the manometer zero point is correct�
2� Connect the manometer to the cooker pressure test point�
This is located on the regulator or LPG inlet fitting�
3� Turn on the gas supply and the electricity (if applicable)
and try to ignite the gas�
NOTE: It will take additional time to light the gas for the first
time, as air needs to be purged from the pipes.
4� Check the operating pressure for the particular gas type
(see 'Gas Type' table)�
•
For LPG cookers: Adjust the regulator if necessary
(this may be remote from the cooker)�
•
For Natural Gas cookers: Regulators are supplied
pre-adjusted and configured by the component
maker for use with Natural Gas� The appliance
installer is not required to make an adjustment to
obtain the correct outlet pressure setting� An arrow
on the base of the regulator indicates the direction of
the gas flow when the inlet and outlet of the regulator
are orientated correctly�
5� When the regulator has been fitted check for leaks from
the connections with soapy water�
Checking regulator function
With the appliance operating, check the outlet pressure:
1� When all the burners of the appliance are operating
at maximum�
2� When the smallest burner of the appliance is operating
at minimum�
Under both these conditions the outlet pressure should
not vary from nominal operating pressure of 1�0kPa
by more then ± 20% (ie ±0�20kPa for Natural Gas)�
If the regulator does not appear to be performing satisfactorily
then check the following points:
1� If the outlet pressure is consistently too low then
•
the inlet pressure may be too low and adjustment
of an upstream regulator may be needed, or
•
an upstream regulator or valve with insufficient flow
capacity may be present in the gas supply line� It may
be necessary to repeat the checks whilst measuring
both the inlet and outlet pressure to determine if the
inlet pressure
is in the range 1�13-5kPa�
2� Check that the regulator has been fitted to the gas supply
line in the correct orientation�
3� Replace the regulator if it fails to perform after the checks�
Testing Burner Performance
•
Observe the flame appearance on each burner when set
to max� If it is smaller or larger than expected, then the
injector size needs checking (refer to table)�
• When maximum flame appearance is correct, check
the turn down setting on each burner� If incorrect, proceed
as follows:
WARNING
WARNING
Disconnect electric power.
1� Remove the control panel and adjust the bypass screw
when valve is set to maximum� The screw is mounted on
the body of each hotplate control valve�
2� Check the ignition on all burners both separately and
in combination�
3� Check the operation of the electrical components,
if applicable�
4� When operating correctly, show customer how to use
the cooker�
5� If not operating correctly, advise the customer to ring
Electrolux Customer Service Centre� Place a warning sign
on cooker or if dangerous, disconnect cooker�
INSTALLATION
