background image

30

INSTALLATION

INSTALLING THE GAS COOKER

GAS CONNECTION

Read these points before connecting to the gas supply:
•   The gas connection point is a 1/2” BSP external 

thread located at the rear of the appliance as shown  

in the Rear View.

•   A regulator is supplied for natural gas appliances which 

must be fitted in the supply line to the appliance. For 

LPG appliances a test point fitting must be fitted to the 

supply line.

•   It is recommended to fit the regulator or test point fitting 

to the appliance connection point, then fit either hard 

piping or a high level flexible connection from the 

regulator or test point fitting to consumer hard piping. 

Ensure installation allows withdrawal of appliance. 

For flexible hose installation AS/NZS 5601.1 clauses 

5.9 and 6.10.1.9 must be followed.

OPERATION ON NG/SNG

Read these points about operation on NG/SNG and look 

carefully at the diagram:
•   The appliance regulator provided MUST be orientated 

so that the pressure nipple is accessible.

•   The arrow showing the direction of the flow MUST be 

pointed correctly.

•   The regulator has a 1/2” BSP internal thread at inlet 

and outlet.

 OPERATION ON SNG

•   If the cooker is to be used with SNG, then the grill 

burner MUST be modified by the replacement of the 

shutter which fits into the throat of the grill burner.

•   You can buy the kit for this modification from your nearest 

spare parts stockist. (Contact Customer Care Centre).

1.   Remove the control panel. Remove the existing NG 

shutter securing screws (as in diagram) and slide 

upwards to disengage from grill burner.

2.   Slide the SNG shutter into position and secure 

with screws.

OPERATION ON UNIvERSAL LPG/PROPANE

An inlet fitting with pressure test point is provided.
The inlet fitting has 1/2” BSP internal thread for both inlet 

and outlet. The inlet fitting must be orientated so that the 

pressure test point is accessible.

WIRING CONNECTION fOR GAS COOKER

To allow for disconnection of the appliance after 

installation, the plug must be accessible after installation, 

or a functional switch must be provided near the appliance 

in an accessible position.

Restraining Device

Anchor Points

Grill Shutter

Pressure test point

NG Regulator

1/2” BSP

Internal  Thread

Connection

Gas

Point

150mm

650mm

Gas Flo

w

Restraining Device

Anchor Points

Grill Shutter

Pressure test point

NG Regulator

1/2” BSP

Internal  Thread

Connection

Gas

Point

150mm

650mm

Gas Flo

w

Restraining Device

Anchor Points

Grill Shutter

Pressure test point

NG Regulator

1/2” BSP

Internal  Thread

Connection

Gas

Point

150mm

650mm

Gas Flo

w

Rear View

Содержание Westinghouse 540 upright cooker



































Отзывы: