Westermo Wolverine DDW-142-12VDC-BP Скачать руководство пользователя страница 14

14

6642-22541

Location of interface ports and LED’s

LED Indicators 

Power connection 

I/O connection 

SHDSL connection 

RS-232 Connection

 

Position

Signal

Direction* Description

No. 1

DSR

Out

Data Set Ready

No. 2

DCD

Out

Data Carrier Detect

No. 3

DTR

In

Data Terminal Ready

No. 4

SG

Signal Ground, not chassis ground

No. 5

RD

Out

Receive Data

No. 6

TD

In

Transmit Data

No. 7

CTS

Out

Clear To Send

No. 8

RTS

In

Request To Send

Female

Pin 1

Pin 8

*  Direction relative this product.

Ethernet connection TX (2 ports) 

Position

Direction*

Description

No.1

In/Out

Transmitted/Received data

No. 2

In/Out

Transmitted/Received data

No. 3

In/Out

Transmitted/Received data

No. 4

Not Connected

No. 5

Not Connected

No. 6

In/Out

Transmitted/Received data

No. 7

Not Connected

No. 8

Not Connected

*  Direction relative this product.

USB 

Position

Direction*

Description

No.1

Out

VBUS

No. 2

In/Out

D–

No. 3

In/Out

D+

No. 4

Out

GND

Shield

In/Out

Connected to protective earth

*  Direction relative this product.

Содержание Wolverine DDW-142-12VDC-BP























Отзывы: