manualshive.com logo in svg

Westermo MRI-120-F4G-PSE Series, Руководство пользователя

Поделиться
Скачать
Westermo MRI-120-F4G-PSE Series Скачать руководство пользователя страница 69

 

65

 

Syntax 

poe powering-mode 802.3af/forced 

Parameters 

802.3af: deliver power if and only if the attached 

PD comply with IEEE 802.3af 

forced: deliver power no maater what PD attached 

Command Mode 

Interface mode 

Description 

Set the Powring mode of PoE 

Examples 

EX 1: 

Set 802.3af powring mode 

Switch(config)# poe powering-mode 802.3af 

EX 2: 

Set forced powering mode 

Switch(config)# poe powering-mode forced 

Syntax 

poe powering-mode 802.3at 2-event/lldp 

Parameters 

2-event: deliver power if and only if the attached 

PD comply with IEEE 802.3at physical layer 

classification 

lldp: deliver power if and only if the attached 

PD comply with IEEE 802.3at data link layer 

classification 

Command Mode 

Interface mode 

Description 

Set the Powring mode of PoE 

Examples 

EX 1: 

Set 802.3at 2-event powring mode 

Switch(config)# poe powering-mode 802.3at 

2-event 

EX 2: 

Set 802.3at lldpforced powering mode 

Switch(config)# poe powering-mode 802.3at lldp 

Syntax 

poe control-mode user/schedule 

Parameters 

user: user mode 

schedule: schedule mode 

Command Mode 

Interface mode 

Description 

Set the control mode of port 

Examples 

Set PoE port 2 to user mode. 

EX 1: 

Switch(config)# interface fa2 

Switch(config-if)# poe control-mode user 

Set PoE port 2 to schedule mode. 

EX 2: 

Switch(config-if)# poe control-mode schedule 

Proudly Distributed by Gross Automation | (877) 268-3700 

www.westermosales.com | [email protected]

Содержание MRI-120-F4G-PSE Series

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды