manualshive.com logo in svg

Westermo MRI-120-F4G-PSE Series, Руководство пользователя

Поделиться
Скачать
Westermo MRI-120-F4G-PSE Series Скачать руководство пользователя страница 105

 

101

 

Send

 

to

 

Query

 

Ports:

 

The

 

unknown

 

multicast

 

will

 

be

 

sent

 

to

 

the

 

Query

 

ports.

 

The

 

Query

 

port

 

means

 

the

 

port

 

received

 

the

 

IGMP

 

Query

 

packets

 

andit

 

is

 

usually

 

the

 

uplink

 

port

 

on

 

the

 

switch.

   

Send

 

to

 

All

 

Ports:

 

The

 

unknown

 

multicast

 

will

 

be

 

flooded

 

to

 

all

 

ports

 

even

 

if

 

they

 

are

 

not

 

member

 

ports

 

of

 

the

 

groups.

   

Discard:

 

The

 

unknown

 

multicast

 

will

 

be

 

discarded.

 

Non

‐

member

 

ports

 

will

 

not

 

receive

 

the

 

unknown

 

multicast

 

streams.

   

 

4.8.4

 

CLI

 

Commands

 

of

 

the

 

Multicast

 

Filtering

 

Command

 

Lines

 

of

 

the

 

multicast

 

filtering

 

configuration

 

 

Feature 

Command Line 

IGMP Snooping 

IGMP Snooping - 

Global 

Switch(config)# ip igmp snooping 

IGMP snooping is enabled globally. Please specify 

on which vlans IGMP snooping enables 

IGMP Snooping - 

VLAN 

Switch(config)# ip igmp snooping vlan 

 VLANLIST  allowed  vlan  list 

 all       all  existed  vlan 

Switch(config)# ip igmp snooping vlan 1-2 

IGMP snooping is enabled on VLAN 1-2. 

Disable IGMP 

Snooping - Global 

Switch(config)# no ip igmp snoopin 

IGMP snooping is disabled globally ok. 

Disable IGMP 

Snooping - VLAN 

Switch(config)# no ip igmp snooping vlan 3 

IGMP snooping is disabled on VLAN 3. 

Display – IGMP 

Snooping Setting 

Switc

evic ip igmp 

interface vlan1 

enabled: Yes 

version: IGMPv1 

Proudly Distributed by Gross Automation | (877) 268-3700 

www.westermosales.com | [email protected]

Содержание MRI-120-F4G-PSE Series

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды