manualshive.com logo in svg

Wenger Gearboss Rival, Руководство по установке, Страница: 18 / 24

Поделиться
Скачать
Wenger Gearboss Rival Скачать руководство пользователя страница 18

18

Installation (continued)

This procedure is for securing island mount lockers to the structure. 

See the previous page for securing wall mount lockers.
This instruction is for standard installation only. 

For seismic installation, see the instructions included with the Seismic Island Kit 243A028.

STOP

Secure Island Mount Lockers

Because materials and construction of walls can vary, fasteners for attaching the lockers to the structure  

are not provided� The installer must choose the appropriate fastener and follow the manufacturer’s instructions�  

See “Fasteners - Not Supplied" on page 5 for more information�

NOTE:  

The end of every locker bank must be secured to the floor.

NOTE:  

Make sure all the lockers are secured together before  

       attaching them to the floor.

1�  At the ends of the locker bank, attach one  

wall bracket (13) to the bottom inside of  

each locker using  

#8 x 5/8" pan head screws (14)�

 

The brackets have extra holes for the  

best fit.

2�  Secure the bracket to the locker  

using #8 x 5/8" pan head screws (14)�

3.  Secure the bracket to the floor using 

 

the appropriate fasteners�

4�  Reattach the bottom shelves in the  

lockers�

5�  Install any optional equipment  

as shown on the following pages  

before continuing to  

“Finalize Installation" on page 23�

In addition to the sides and backs of the lockers being 

secured, the lockers must also be attached to the floor.

!

CAUTION

Attach to the 

locker using  

#8 x 5/8"  

Pan Head Screws  

(14)

Wall 

Bracket  

(14)

Slide 

shelf in

Reattach 

screws

Inferior or improperly installed fasteners 

could cause the lockers to tip over.

!

WARNING

Содержание Gearboss Rival

























Отзывы:

Нет отзывов