Wenger Gearboss AirPro Скачать руководство пользователя страница 2

2

Important User Information

General

Copyright © 2016 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted 

in any form or by any means including graphic, electronic, or mechanical methods or photocopying, 

recording, or information storage and retrieval systems without the written permission of the publisher, 

unless it is for the purchaser’s personal use. 
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment 

on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any 

errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, 

indirect, special, incidental, or consequential damages resulting from the use or defect of this manual.
The information in this document is not intended to cover all possible conditions and situations that might 

occur. The end user must exercise caution and common sense when assembling or installing Wenger 

Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-887-7145.

Manufacturer

The GearBoss

®

 AirPro

 Locker is manufactured by:

 

Wenger Corporation 

 

555 Park Drive 

 

Owatonna, MN  55060 

 

800-4WENGER (493-6437) • 1-507-455-4100 

 www.wengercorp.com

Intended Use

· 

This product is intended for indoor use in normal ambient temperature and humidity conditions  

 

— it must not be exposed to outside weather conditions. 

· 

This product is intended to be assembled only as described in these instructions.

Warranty

GearBoss AirPro Lockers are covered under a ten year Limited Warranty offered to you,  

the initial purchaser. This Warranty runs from the date of shipment and warrants that the Wenger 

product will be free of defects in materials or craftsmanship during the warranty period.  

This Warranty is your sole and exclusive remedy for any claim against Wenger related to your  

purchase, use, or ownership of a Wenger product. This Warranty does not apply to damage caused by 

common carrier, misuse or abuse, alterations to products not expressly authorized by Wenger. 

Exact matching of color, grain, texture and lighting is not guaranteed as these features are prone to 

change and fade over time. Our warranty assures you of, at the discretion of our Customer Service 

Department, either a full refund, or the repair or replacement of the defective product without charge. 

Just call a Customer Service Representative at 1-800-887-7145 and state the reason you are 

dissatisfied. If return of a product is necessary, your representative will issue a return authorization.

The Warranty assumes proper use and care of the Lockers. Care must be given by locker users not to 

stuff foot lockers over capacity and then attempt to compress the gear using the seat. Evidence of this 

misuse will be bending and failure of the seat hinges. 

An intentional benefit of GearBoss Lockers are repairable and replaceable parts. To achieve this 

through-bolts are used and on moving parts and the vibration of these connection points can, at times, 

cause bolts to loosen. Maintenance must be in place to annually check and, if necessary, tighten bolts at 

these locations as shown below.  Evidence of a failure to provide this maintenance will be seat hinges or 

lock brackets that have come loose.

Содержание Gearboss AirPro

































Отзывы: