Wenger Fixed Media Cabinets Скачать руководство пользователя страница 2

2

Important User Information

General

Copyright© 2014 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted 

in any form or by any means including graphic, electronic, or mechanical methods or photocopying, 

recording, or information storage and retrieval systems without the written permission of the publisher, 

unless it is for the purchaser’s personal use. 
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment 

on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any 

errors that may appear in this manual.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for 

direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this 

manual.
The information in this document is not intended to cover all possible conditions and situations that 

might occur. The end user must exercise caution and common sense when assembling or installing 

Wenger Corporation products. If any questions or problems arise, call Wenger Corporation at 1-800-

887-7145.

Manufacturer

The Media Storage Systems are manufactured by:

 

Wenger Corporation 

 

555 Park Drive 

 

Owatonna, MN  55060 

 

1-800-4WENGER (493-6437) • 1-507-455-4100 

 www.wengercorp.com

Intended Use

· 

This product is intended for indoor use in normal ambient temperature and humidity conditions —  

 

it must not be exposed to prolonged outside weather conditions.

· 

This product is intended to be assembled and used only as described in these instructions.

Warranty

This product is guaranteed free of defects in materials and workmanship for ten full years from  

date of shipment. A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the  

individual manufacturer’s warranty.

Содержание Fixed Media Cabinets

















Отзывы: