background image

BRAD NAILER & STAPLER SAFETY WARNINGS

BRAD NAILER & STAPLER SAFETY

1.  THIS TOOL IS DESIGNED for household use 

only, not for industrial or professional purposes. Do 

not force the tool to do a job for which it was not 

designed. 

2.  INSPECT TOOL BEFORE USE. Do not operate if 

any portion of the tool, trigger, or safety bracket 

is damaged, inoperable, disconnected, or altered. 

Leaking air, damaged parts, or missing parts should 

be repaired or replaced.

3. GRIP THE TOOL FIRMLY with both hands to 

maintain control while still allowing it to recoil away 

from the work surface as the fastener is driven. 

4. KEEP FACE AND BODY PARTS AWAY from the 

back of the tool cap when working in restricted 

areas. Sudden recoil can result in impact to the body, 

especially when nailing into hard or dense material.

5. DO NOT DISCHARGE fasteners into open air, 

concrete, stone, extremely hard woods, knots or any 

material too hard for the fastener to penetrate. 

6. DO NOT DRIVE FASTENERS near the edge of your 

work material. The workpiece may split, causing the 

fastener to ricochet, injuring you or a bystander. 

Be aware that the fastener may follow the grain of 

the wood, causing it to protrude unexpectedly from 

the side of the work material. Drive the fastener 

perpendicular to the grain to reduce risk of injury.

7. DO NOT DRIVE FASTENERS onto the heads of 

other fasteners. Do not use the tool at too steep of 

an angle. Personal injury from strong recoil, jammed 

fasteners, or ricochetted nails may result.

 

8. BE AWARE of material thickness when using the 

nailer. A protruding nail may cause injury.

9. WHEN THE TOOL IS BEING UTILIZED AT 

PRESSURES ON THE HIGH END of its operating 

range, fasteners can be driven completely through 

thin or very soft work material. Make sure the 

pressure in the compressor is set so that fasteners 

are set into the material and not pushed completely 

through.

10. REMOVE FINGER FROM TRIGGER when not 

driving fasteners. Never carry the tool with your 

finger on the trigger.

11. IF THE FASTENERS ARE JAMMED, disconnect 

the tool from the air supply first before removing the 

jammed fasteners.

12. DISCONNECT tool from air supply when not in 

use. Remove fasteners from magazine before leaving 

the area or passing the tool to another operator. Do 

not climb ladders, stairs, scaffoldings, etc. without 

disconnecting the tool. Do not carry a connected 

tool to another work area. Do not make adjustments, 

remove magazine, perform maintenance or clear 

jammed fasteners while connected to the air supply. 

13. DO NOT REMOVE, tamper with, or otherwise 

cause the tool, trigger or safety bracket to become 

inoperable. Do not tape or tie the trigger or safety 

bracket in the ON position. Do not remove springs 

from the safety bracket. Make daily inspections for 

free movement of the trigger and safety bracket. Do 

not alter or modify the tool in any way. 

14. MAINTAIN TOOLS PROPERLY. Always keep tools 

clean and in good working order. Follow instructions 

for lubricating, changing accessories and storage. 

WARNING!

 Do not let comfort or familiarity with the product replace strict adherence to product safety rules. 

Failure to follow the safety instructions may result in serious personal injury. 

6

Содержание 61722

















Отзывы: