background image

18

To adjust the idle speed

1. Make sure that the air filter is clean and the air filter

cover is installed.

2. Adjust the idle speed with the idle adjustment screw.

The idle adjustment screw T is identified with a "T"

mark.

3. Turn the idle adjustment screw clockwise until the

cutting attachment starts to turn.

4. Turn the idle adjustment screw counterclockwise

until the cutting attachment stops.

The idle speed is correct when the engine operates

smoothly in all positions. The idle speed must be below

the speed when the cutting attachment starts to turn.

WARNING: If the cutting attachment does

not stop when you adjust the idle speed,

Speak

 

to

 

Wemars

 

service

 . Do not 

use

 

the

 

product until it is correctly adjusted 

or

 

repaired

.

T

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct.

• Replace the spark plug if it is necessary.

To do maintenance on the trimmer

head

1. Only use the recommended cutting attachment and

cutting attachment guard. 

2. Make sure that the cutter on the cutting attachment

guard is not damaged, it cuts the cord to the correct

length.

3. Install the cord as the illustrations on the last pages

of the manual shows.

Air filter

Remove dust and dirt from the air filter to keep it clean in

order to prevent:
• Carburettor malfunctions.
• Starting problems.
• Loss of engine power.
• Unnecessary wear to engine parts.
• Too much fuel consumption.
Clean the air filter at an interval of 25 hours, or more

regularly if conditions are unusually dusty.

To clean the air filter

CAUTION: A air filter that is damaged, very

dirty or soaked with fuel must always be

replaced.

If you use an air filter for a long time it cannot be fully

cleaned. Replace the air filter with a new one at regular

intervals.

Содержание WS-ST42G






















Отзывы: