Weldclass WeldForce WF-135s stick Скачать руководство пользователя страница 17

Страница: 17 / 20

Arc rays from the welding process produce intense

heat and strong ultraviolet rays that can burn eyes

and skin. Use the following table to select the

appropriate shade number for a Welding Helmet

or Welding Face Shield.

11. Do not touch the electrode while in contact

with the work (ground) circuit.

12. Use only well-maintained equipment. Repair

or replace damaged parts as soon as practical.

13. In confined spaces or damp locations, do not

use a welder with AC output unless equipped

with a voltage reducer.

1. Use a Welding Helmet or Welding Face Shield

fitted with a proper shade of filter (see AS

60974-1, AS/NZS 1337.1 and AS/NZS 1338.1

Safety Standards) to protect your face and

eyes when welding or watching.

2. Wear approved safety glasses. Side shields are

recommended.

3. Use protective screens or barriers to protect

others from flash and glare; warn others not to

watch the arc.

4. Wear protective clothing made from durable,

flame-resistant material (wool and leather)

and foot protection.

5. Never wear contact lenses while welding.

Содержание WeldForce WF-135s stick





















Результаты поиска

Содержание WeldForce WF-135s stick

Отзывы:

Бренды по названию

Популярные бренды

Weldclass WeldForce WF-135s stick, Руководство по эксплуатации

Результаты поиска

Содержание WeldForce WF-135s stick

Отзывы:

Бренды по названию

Популярные бренды