manualshive.com logo in svg

Welch Allyn IMAGETEAM 3800, Руководство пользователя

Поделиться
Скачать
Welch Allyn IMAGETEAM 3800 Скачать руководство пользователя страница 95

Section 8

Cloning

8–1

IMAGETEAM 3800 User’s Guide

The cloning procedure reprograms the software in the “destination” scanner’s
memory with software from the “source” scanner.  Before using this procedure,
determine which scanner will be the source (the scanner containing the desired
software).  The IMAGETEAM 3800 supports cloning and can act as the source
device.  The software in the destination scanner will be updated from the
source scanner.  The destination scanner device must be the same model as
the source.

Procedure:

1.

Use the cloning cable (42204559–01) to connect the two scanners
for cloning.

2.

Connect the destination scanner to one of the 10 pin modular
connectors on the cloning cable.

3.

Connect the source scanner (containing the new or updated
software) to the remaining 10 pin modular connector on the cloning
cable.

4.

Connect the power supply to the 4 pin mini–DIN connector located
on the cloning cable or the scanner cable.

5.

Make sure both units are on, and then scan the “Clone Destination”
bar code with the destination scanner.

Clone Destination Bar Code

6.

Scan the Clone Source bar code below with the source scanner.
The scanner’s “Good Read” LED begins blinking periodically
indicating cloning is in process. 

Clone Source Bar Code

7.

When cloning is complete, the destination scanner will double beep.
This procedure takes approximately two minutes.

8.

Disconnect the destination scanner from the cloning cable.

9.

To clone another scanner, repeat steps 1 through 8.

Caution: DO NOT scan the “source” bar code unless you are

going to clone a scanner.  If you mistakenly scan this
bar code, reset the scanner by turning the power off
and back on to regain normal operation.

Содержание IMAGETEAM 3800





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды