manualshive.com logo in svg

Welch Allyn IMAGETEAM 3800, Руководство пользователя

Поделиться
Скачать
Welch Allyn IMAGETEAM 3800 Скачать руководство пользователя страница 19

2–5

IMAGETEAM 3800 User’s Guide

Keyboard Style

This programs keyboard styles, such as Caps Lock and Shift Lock.  Default =
Regular.

Regular is used when you normally have the Caps Lock key off.

* Regular

Caps Lock is used when you normally have the Caps Lock key on.

Caps Lock

Shift Lock is used when you normally have the Shift Lock key on.  (Not
common to U.S. keyboards.)

Shift Lock

Automatic Caps Lock is used if you change the Caps Lock key on and off.
The software tracks and reflects if you have Caps Lock on or off (AT and PS/2
only). This selection can only be used with systems that have an LED which
notes the Caps Lock status.

Automatic Caps Lock

Emulate External Keyboard should be scanned if you do not have an external
keyboard (IBM AT or equivalent).  To connect the scanner to a laptop, it may be
necessary to use the Automatic Direct Connect selection on page 2–7 in
conjunction with the bar code below.

Emulate External Keyboard

Содержание IMAGETEAM 3800





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды