Welch Allyn IMAGETEAM 3800 Скачать руководство пользователя | Manualshive

Страница: 59 / 132

background image

7–3

IMAGETEAM 3800 User’s Guide

Industrial Symbology Selections

Codabar, continued

Check Character

Codabar check characters are created using different “modulos.” You can
program the scanner to read only Codabar bar codes with Modulo 16 check
characters. Default = No Check Character.

No Check Character indicates that the scanner reads and transmits bar code
data with or without a check character.

When Check Character is set to Validate and Transmit, the scanner will only
read Codabar bar codes printed with a check character, and will transmit this
character at the end of the scanned data.

When Check Character is set to Validate, but Don’t Transmit, the unit will only
read Codabar bar codes printed with a check character, but will not transmit
the check character with the scanned data.

* No Check Character

Validate Modulo 16, but

Don't Transmit

Validate Modulo 16 and Transmit

«
...
57
58
59
60
61
...
»

Содержание IMAGETEAM 3800





































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMAGETEAM 3800

Бренд: Unitech Страницы: 18

Бренд: Unitech Страницы: 2

Бренд: Custom Audio Electronics Страницы: 16

Бренд: Magtek Страницы: 2

Бренд: Pocketbook Страницы: 105

Бренд: IDEC Страницы: 39

Бренд: Datalogic Страницы: 32

Бренд: Salto Страницы: 5

Бренд: ACS Страницы: 45

PocketMate II ACR39U-N1

Бренд: ACS Страницы: 44

Бренд: Creator Страницы: 16

Бренд: Infinite Peripherals Страницы: 28

Бренд: TSYS Страницы: 83

Бренд: Obreey Страницы: 107

Бренд: Optoelectronics Страницы: 26

Бренд: Optoelectronics Страницы: 41

Бренд: Encore Страницы: 5

Energy eReader Slim

Бренд: ENERGY SISTEM Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды