manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

5 Installation

83309302 1/2018-05 La

40-196

5.3 Gas supply

Only an approved gas installer may carry out the gas side connection. Observe
local regulations.

The gas characteristics must match the data given on the name plate of the appli-
ance.

The appliance is factory preset to Natural Gas.

Conversion from Natural Gas to Liquid Petroleum Gas [ch. 7.1.3].

Gas connection pressure

During operation, the gas connection pressure must be within the following range:

Natural Gas E/H

17.0 … 

20

 … 25.0 mbar

Natural Gas LL

20.0 … 

25

 … 30.0 mbar

LPG B/P (p

n

 37)

25.0 … 

37

 … 45.0 mbar

LPG B/P (p

n

 50)

42.5 … 

50

 … 57.5 mbar

Operation outside the ranges according to EN 437 is not permitted.

Installing the gas supply

DANGER

Risk of explosion due to leaking gas

Gas leaks can lead to a build-up of explosive gas/air mixture. With an ignition
source present this can result in an explosion.

Install gas supply with care.
Observe all safety instructions.

Close fuel shut off devices prior to commencing work and protect from acci-
dental re-opening.
Install gas supply pipes tension free.
Connect gas supply to gas isolating valve 

1

.

1

Carry out soundness test of gas supply line and vent

Only the gas supply company or a contract installation company may carry out a
soundness test and vent the gas line.

Gas safety valve

The gas safety valve opens only when the output is configured, therefore the flue
gas measurement must be skipped during initial commissioning and carried out
later.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

vacuubrand BVC control Instruction Manual preview
BVC control
Бренд: vacuubrand Страницы: 76
Warner Instruments SHM Series Instructions preview
SHM Series
Бренд: Warner Instruments Страницы: 3
WarmPool WP120 Installation And Operation Manual preview
WP120
Бренд: WarmPool Страницы: 26
Warmlite WL42006 Safety & Instruction Manual preview
WL42006
Бренд: Warmlite Страницы: 8
Lennox Signature XP19-024 Installation Instructions Manual preview
Signature XP19-024
Бренд: Lennox Страницы: 32
QualityCraft MCVT120-150 Quick Start Manual preview
MCVT120-150
Бренд: QualityCraft Страницы: 10
Reality Leuchten R087-01 Manual preview
R087-01
Бренд: Reality Leuchten Страницы: 86
Grundfos NBS Service Instructions Manual preview
NBS
Бренд: Grundfos Страницы: 35
Master B100CED Owner'S Manual preview
B100CED
Бренд: Master Страницы: 187
Durapac DPR-223 Instruction Manual preview
DPR-223
Бренд: Durapac Страницы: 11
KNF N630.12 Translation Of Original Operating And Installation Instructions preview
N630.12
Бренд: KNF Страницы: 88
Eco Heat 1C750W2 User Manual preview
1C750W2
Бренд: Eco Heat Страницы: 2
York YCUL0020 Installation, Operation And Maintenance Manual preview
YCUL0020
Бренд: York Страницы: 178
Vectra Fitness FM-1309-Z User Manual preview
FM-1309-Z
Бренд: Vectra Fitness Страницы: 28
Aktobis D033FT Instruction Manual preview
D033FT
Бренд: Aktobis Страницы: 5
ProMinent Hydro 3 Series Operating Instructions Manual preview
Hydro 3 Series
Бренд: ProMinent Страницы: 96
Zoeller AQUANOT 585 Manual preview
AQUANOT 585
Бренд: Zoeller Страницы: 8
American Standard 2A7A8 Installer'S Manual preview
2A7A8
Бренд: American Standard Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды