manualshive.com logo in svg

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Weishaupt WTC-GB 15-B Compact - Компактный газовый котел с инструкцией по монтажу и эксплуатации. Можно скачать бесплатно на manualshive.com для получения руководства пользователя. Удобное решение для вашего дома.

Поделиться
Скачать
background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

7 Commissioning

83309302 1/2018-05 La

104-196

7.1.2 Check gas connection pressure

DANGER

Risk of explosion due to excess gas supply pressure

Exceeding the maximum connection pressure can damage the gas valve train and
lead to an explosion.

Check gas connection pressure

Open screw on test point Pe of gas combi valve [ch. 7.1.1].
Connect pressure measuring device.
Slowly open isolating valve whilst observing the pressure increase.

If the connection pressure exceeds 60 mbar:

Immediately close isolating valve.
Do not start plant.
Inform the gas supplier.
If necessary install gas pressure regulator.

DANGER

Risk of explosion due to leaking gas

Improper service work can lead to escaping gas and explosion.

After working on the gas combi valve, close the screw at the measuring point
and check for leaks.

Close screw on measuring point Pe (torque 2 Nm).
Check soundness of measuring point.

7.1.3 Set type of gas on gas combi valve

The gas combi valve is factory reset to Natural Gas.

If the appliance is operated with liquid petroleum gas, it is necessary to switch to
LPG at the gas combination valve:

Turn screw (Allen screw 2.5) 

1

 90° clockwise to position 2.

Natural Gas

Position 1

LPG

Position 2

1

If the type of gas is changed, the parameter for the type of gas must also be adjus-
ted.

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

KASTOR K Series Installation And Operating Instructions Manual preview
K Series
Бренд: KASTOR Страницы: 40
VARISCO K Series Instructions For Use And Maintenance Manual preview
K Series
Бренд: VARISCO Страницы: 52
DAYLIFF DFP Installation & Operating Manual preview
DFP
Бренд: DAYLIFF Страницы: 12
WAGNER Wildcat 10-70 Translation Of The Original Operation Manual preview
Wildcat 10-70
Бренд: WAGNER Страницы: 100
Danfoss PAHT Series Service Manual preview
PAHT Series
Бренд: Danfoss Страницы: 22
Olimpia splendid Caldo Rock M Instructions For Installation, Use And Maintenance Manual preview
Caldo Rock M
Бренд: Olimpia splendid Страницы: 104
TapFlo PTL Series Manual preview
PTL Series
Бренд: TapFlo Страницы: 63
Qlima SRE 70x-TC Operating Manual preview
SRE 70x-TC
Бренд: Qlima Страницы: 14
Thermor Aeromax Piscine 10 Installation And User Manual preview
Aeromax Piscine 10
Бренд: Thermor Страницы: 32
Seville Classics ULTRASlimline 10222 Instruction Manual preview
ULTRASlimline 10222
Бренд: Seville Classics Страницы: 6
Regulus CTC EcoPart 400 Installation And Maintenance Manual preview
CTC EcoPart 400
Бренд: Regulus Страницы: 26
ACE INSTRUMENTS DPI-2200 Instruction Manual preview
DPI-2200
Бренд: ACE INSTRUMENTS Страницы: 3
B-TEC IR-B01-B User Manual preview
IR-B01-B
Бренд: B-TEC Страницы: 11
Wacker Neuson PS3 1500 Operator'S Manual preview
PS3 1500
Бренд: Wacker Neuson Страницы: 52
Olimpia splendid B0658 Instructions For Mounting And Use preview
B0658
Бренд: Olimpia splendid Страницы: 12
UNITED UHR-865 Instruction Manual preview
UHR-865
Бренд: UNITED Страницы: 8
Annovi Reverberi AR202 Instruction Manual preview
AR202
Бренд: Annovi Reverberi Страницы: 100
Rheem RTHP009 Installation Maintenance And Service Manual preview
RTHP009
Бренд: Rheem Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды