manualshive.com logo in svg

Weil-McLain Aqua Logic, Руководство по эксплуатации продукта, Страница: 34 / 44

Поделиться
Скачать
Weil-McLain Aqua Logic Скачать руководство пользователя страница 34

A

QUA

 L

OGIC

  

COMPANION

 

WATER

 

HEATER

 — 

Product Manual

Troubleshooting 

(continued)

Boiler relief valve lifting or weeping

1  Undersized expansion tank? 

s

Insufficient allowance for expansion on the boiler side can cause the boiler pressure relief valve to lift.

s

The tank must be sized to handle the total volume of water in the boiler system, the boiler and all intercon-
necting piping. The volume for the Aqua Logic (CWH) boiler piping and heat exchanger is 1.4 gallons.

2  Faulty boiler expansion tank? 

s

Is the expansion tank defective, waterlogged or improperly charged? 

s

Check for failed gaskets or bladders, or a faulty Schraeder valve.

s

Tank must be isolated and pressure relieved from boiler side when testing.

s

Use a tire gauge to check the charge pressure of the tank.

s

Turn the boiler limit up to a higher setting and let the system run at a higher temperature. This will 
simulate maximum expansion in the boiler system.

s

If the boiler relief valve lifts and/or there is a significant increase in the boiler system pressure, the 
expansion tank is flooded or undersized.

3  Faulty boiler relief valve? 

s

Is the boiler pressure relief valve functioning properly? Dirt and water deposits can accumulate under 
the valve seat. 

4  Faulty boiler fill valve? 

s

Is the valve filling to the correct pressure? 

5 Tank heat exchanger coil leaking? 

s

Turn the boiler power OFF.

s

Close the boiler supply and return isolation valves.

s

Isolate the water heater from the domestic water system by closing isolation valves.

s

Attach a hose to the water heater drain valve (if not directly connected to a drainage location).

s

Open the water heater drain valve to allow the tank-side pressure to drop.

s

Watch the pressure on the boiler P/T gauge. If this pressure drops noticeably, there is a leak in the piping 
or in the tank heat exchanger. Locate the problem and correct. Replace the Aqua Logic (CWH) tank if 
necessary.

Part number 635-500-156/1113

34

Содержание Aqua Logic













































Отзывы:

Нет отзывов