Weider 831.153921 Скачать руководство пользователя страница 3

1. Read all instructions in this manual before

using the resistance system. Use the resist-

ance system only as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the resistance system are

adequately informed of all precautions.

3. The resistance system is intended for home

use only. Do not use the resistance system in

any commercial, rental, or institutional setting.

4. Use the resistance system only on a level

surface. Cover the floor beneath the resist-

ance system to protect the floor.

5. Make sure that all parts are properly tight-

ened each time the resistance system is

used. Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the resistance system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion while exercising.

9. The top frame is not designed to be used for

pull-up exercises. Do not hang on the top

frame.

10. Always disconnect the lat bar from the short

cables when performing an exercise that

does not require it.

11. The resistance system is designed to sup-

port a maximum user weight of 300 pounds.

12. Pull on the low pulley cable only while sitting

on the bench or standing on the base plate.

Pull on the high pulley cables only while sit-

ting on the bench, with the seat in one of the

three positions closest to the upright base,

or while standing on the base plate.

13. The resistance system is designed to be

used with the included resistance, and the

resistance included with a CrossBar by WEI-

DER

Power Pak. Do not use the resistance

system with any other type of resistance.

14. When adding resistance, both ends of the

resistance bars must rest under the two “U”-

channels. Add and remove resistance bars

from the “U”-channels one resistance bar at

a time.

15. Keep clear of the area around the “U”-chan-

nels while the resistance system is in use.

Do not add or remove resistance bars from

the “U”-channels while the end of the long

cable is pulled out.

16. Make sure that the cables remain on the pul-

leys at all times. If the cables bind as you are

exercising, stop immediately and make sure

that the cables are on the pulleys. Replace all

cables at least every two years.

17. Keep the resistance system indoors, away

from moisture and dust. Do not put the

resistance system in a garage or covered

patio, or near water.

18. If you feel pain or dizziness while exercising,

stop immediately and begin cooling down.

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. Sears assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

3

WARNING:

To reduce the risk of serious injury, read the following important precautions

before using the resistance system.

IMPORTANT PRECAUTIONS

Содержание 831.153921

























Отзывы: