background image

 22

 

BY A TRAINED AND EXPERIENCED TECHNICIAN. Ensure that the work area is clean and free 
of debris prior to starting any maintenance or service work. Small particles may become trapped 
in key components that may lead to serious damage to the machine and cause severe bodily 
harm to the operator or technician.

 

 

Use WEIBANG brand-name parts for compatibility and optimum performance. Use of 
any other parts prior to consulting with your local dealer will void all warranties 

 

10.3.2 Pre-maintenance

 

1

. When this equipment is stopped for servicing, inspection, storage, or to make adjustments, 

make sure the spark plug wire is disconnected from the spark plug. Also, make sure the engine 
has cooled down before you make any inspections, adjustments, etc. 

2. 

Use only original WEIBANG replacement parts. Parts from other manufacturers could be 

dangerous during operation even though they may appear to fit properly.

 

3.

 

There are two grease zerks that need periodic greasing: there is one zerk located on the right 

side bearing housing, and one on the left side bearing housing, (as viewed from behind 
handlebars) grease these locations every 50 hours of use or as needed. 

4. 

Make certain all safety decals on this equipment are kept clean and in good condition. The 

decals are shown (at reduced sizes) before. All decals are available for replacement except that 
with the serial number of the unit for each number serves as an unique identifier for warranty and 
support purposes. If you need a replacement decal, please call your dealer for re-ordering.

 

WARNING: Do not leave machine unattended or attempt any inspection or service unless 
the engine is stopped. Remove spark plug wire from spark plug. Allow machine to come to 
a complete stop.

 

General recommendations 

The warranty on this sod cutter does not cover articles that have been subjected to operator 
abuse or negligence. To maintain a complete coverage by the warranties provided, the operator 
must maintain the sod cutter as instructed in this manual. For a proper maintenance of your sod 
cutter, some adjustments will need to be made periodically. All adjustments in the Service 
Adjustments section of this manual should be checked at least once each season.

 

Replace the sparkplug, clean or replace the air filter element and check blade(s) for wear once 

very year. A new spark plug

and a cleaned or new air filter element, assures a proper air-fuel 

mixture and helps your engine run better and last longer.   

Observe the maintenance schedule in this manual. 

WARNING: MAKE SURE DO CARRY OUT ALL MAINTENANCE AND SERVICE WORKS 

WHILE THE ENGINE IS STOPPED.

 

10.3.3 Maintenance contents 

BEFORE EACH USE 

Check engine oil liquid level. 

Check for loose screws, nuts, bolts or fasteners.

 

expressed herein. 

Содержание WBSC457LC































Отзывы: