background image

 10

 

1.  Bumper, Used for protecting the engine and the towing the machine. 

2.

 

Blade-controlling handle

used for controlling cutting depth and blade angle.

3.    Upper locking lever,  used together with blade controlling handle for setting different cutting depth. 
4.  Lower locking lever, used together with blade controlling handle for adjusting the blade 

cutting angle. 

5.  Gear-selecting lever, used for selecting gears to change driving speed. 
6.  Blade-engaging lever, used for control the running and stopping of the blade, which include a 

locking lever and a shifting lever. 

7.

 

Handle bar, used for controlling the direction of machine's travelling.

 

8.  Throttle-controlling lever, used for stopping or accelerating the machine. 
9.    Belt- clutch handle

for engaging or disengaging the gearbox with engine. 

10.  Oil gauge, used for observing oil quality and liquid level. 

12.

 

Travelling wheel, intalled on driving wheel, used for short distance (less than 1000m) transferr-

one jobsite to 

ing from another. Remove the wheel before cutting sod. 

 

13.  Starting knob, used for recoil starting the engine. 

Engine lubrication oil

 

For oil type, viscosity and capacity please refer to engine manual. 

Lubrication oil for engine gear box

 

For gear oil type, viscosity and capacity please refer to engine manual. 

Lubrication oil for transmission system

 

1.

 

If transmission box need maintenance, please contact your local dealer. 

 

2.

 

The transmission system uses vehicles gear oil, which can be observed by vision through an 
oil level gauge on transmission case. The oil should be replaced after first 500 working hours 
and every1000 hours later. Adding oil in time when the liquid level is below the window of oil 
gauge.

 

3.   

Greasing all zerks every 10 hours 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bumper

Starting knob

Blade controling handle

Throttle controlling lever

Handle bar

Belt-clutch lever

Oil gauge

Upper locking lever

Gear selecting lever

Crank

Lower locking lever

Blade engaging lever

Driving wheel

Blade

11.  Driving wheel, for pressing lawn and selpropelling. 

Содержание WBSC457LC































Отзывы: