manualshive.com logo in svg

WEG SSW900 Series, Руководство пользователя, Страница: 22 / 65

Поделиться
Скачать
WEG SSW900 Series Скачать руководство пользователя страница 22

OPERATION IN THE ETHERNET/IP NETWORK

6 OPERATION IN THE ETHERNET/IP NETWORK

6.1 CYCLIC DATA

Cyclic data is the data normally used for status monitoring and equipment control. For EtherNet/IP protocol, the
interface supports an I/O connection that allows communication up to 50 input words and 20 output words.

It is necessary the configuration to be made both at the slave and master.

6.1.1

Input words

The SSW900 soft-starter has a reading area with 50 16-bit words available for cyclic data exchange of communication
networks. The data available in the reading area (Input) is sent to the master of the network. This area is shared
between the two Slots.

To map an object in the reading area, follow the steps below.

1. Configure parameter C8.1.1.1 (Slot 1) or C8.1.1.3 (Slot 2). Those parameters indicate which of the reading

words starts the input area for the specific Slot.

2. Configure on parameter C8.1.1.2 (Slot 1) or C8.1.1.4 (Slot 2) the quantity of input words which must be

transmitted via network.

3. Parameters C8.1.1.5 to C8.1.1.54 enable to configure the data that must be provided on the reading words.

Those parameters must contain the network addresses (Net Id) of the data that must be transmitted on the
respective reading words. The Net Id list is available on the table A.2. Consider the size of each parameter
mentioned in this list when programming each word.

Example

The example below presents a configuration for Slot 2. Considering the following parameters to be mapped:

S5.1.1 Status Word SSW.
S1.2.4 Main Line Voltage Average.
S1.1.4 Current Average.
S1.5.4 Output Power & P.F. P. F..

Searching parameter information on the table A.2:

Mapped Parameter

Net Id

Size

Qty Mapped Words

Example Value

S5.1.1 Status Word SSW

680

16bit

1

99 = 0063h

S1.2.4 Main Line Voltage Average

4

16bit

1

2186 = 088Ah

S1.1.4 Current Average

24

32bit

2

23 = 00000017h

S1.5.4 Output Power & P.F. P. F.

8

8bit

1

14 = 0Eh

Therefore, the configuration must be performed as shown below:

1. C8.1.1.3 Data Read Slot 2 1st Word = 26

→

first word transmitted via network is the word #26.

2. C8.1.1.4 Data Read Slot 2 Quantity = 5

→

sum of the column “Qty mapped words”.

3. Table 6.1 presents the configuration parameters of the words and the content of the reading words.

SSW900 | 22

Содержание SSW900 Series


































































Отзывы:

Нет отзывов