manualshive.com logo in svg

WEG SSW900 Series, Руководство пользователя, Страница: 15 / 65

Поделиться
Скачать
WEG SSW900 Series Скачать руководство пользователя страница 15

C CONFIGURATIONS

5 C CONFIGURATIONS

This menu allows the programming of all SSW configuration parameters.

C8 COMMUNICATION

To change information via communication network, the SSW has several standard protocols.

The following necessary accessories and protocols are available:

Protocol

Accessory

CANopen

SSW900-CAN-W

DeviceNet

SSW900-CDN-N, SSW900-CAN-W

EtherNet/IP

SSW900-CETH-IP-N

Modbus RTU

SSW900-CRS485-W

Modbus TCP

SSW900-CMB-TCP-N

Profibus DP

SSW900-CPDP-N

PROFINET IO

SSW900-CPN-IO-N

For further details regarding the SSW configuration to operate these protocols, refer to the SSW Communication
Manual.

C8.1 I/O Data

Configure network data exchange area.

Use this for cyclic communication over SSW900-CAN-W module (DeviceNet), SSW900-CPDP-N, SSW900-CDN-N,
SSW900-CETH-IP-N and SSW900-CPN-IO-N. For SSW900-CRS485-W using Modbus RTU protocol or SSW900-
CMB-TCP-N module, a contiguous area of holding registers (@1500-@1549 and @1600-@1619) can be accessed
using standard Modbus functions.

Slot 1

Slot 2

Data write

to

to

word

#

1 = Net Id

word

#

26 = Net Id

word

#

25 = Net Id

word

#

50 = Net Id

1

◦

word = 1

1

◦

word =26

Quantity = 25

Quantity = 25

Data read

to

to

Slot 1

Slot 2

Word

#

1 = Net Id

Word

#

11 = Net Id

Word

#

10 = Net Id

Word

#

20 = Net Id

1

◦

Word = 1

1

◦

Word =11

Quantity = 10

Quantity = 10

{

{

{

{

Figure 5.1:

Example of data setting

C8.1.1 Data Read

Configure a set of 16 bit parameters to read over the network.

C8.1.1 Data Read

C8.1.1.1 Slot 1 1st Word

Range:

1 ... 50

Default:

1

Properties:

Stopped

SSW900 | 15

Содержание SSW900 Series


































































Отзывы:

Нет отзывов