WEG SRW 01 Скачать руководство пользователя

Страница: 130 / 148

Diagnosis

7-2 | SRW 01

7.2 DIAGNOSIS VIA HMI

Table 7.3:

Error code

Error

Type

Action

Description

E0003

Protection

Trip or alarm

Phase loss (voltage)

E0004

Protection

Trip

Phase sequence

E0005

Protection

Trip or alarm

Overload

E0009

System

Error

EEPROM error

E0010

System

Fault

Error copy function

E0015

Protection

Trip or alarm

Phase loss (current)

E0016

Protection

Trip or alarm

Undervoltage

E0017

Protection

Trip or alarm

Overvoltage

E0018

Protection

Trip or alarm

Voltage unbalance

E0024

System

Error

Digital output configuration error

E0025

System

Error

Digital input configuration error

E0030

System

Error or fault

Control Unit without communication with the EDU

E0031

(*)

System

Error or fault

Control Unit without communication with the HMI

E0032

Protection

Trip or alarm

PTC protection

E0034

System

Error

Shorted PTC

E0035

System

Error

Open PTC

E0051

System

Fault

Fault by saving program

E0055

System

Fault

Program incompatible or out of the memory limits

E0056

System

Fault

CRC error during user program transfer

E0060

System

Error

Ethernet interface error

E0065

Protection

Trip or alarm

Undercurrent

E0066

Protection

Trip or alarm

Overcurrent

E0073

Protection

Trip or alarm

Earth fault

E0074

Protection

Trip or alarm

Current imbalance

E0075

Protection

Trip or alarm

Frequency out of range

E0076

Protection

Trip or alarm

Earth leakage

E0077

(**)

Protection

Error or alarm

Earth leakage: Inhibits Trip in case of short circuit

E0078

System

Error

Check back error, verification of start control

E0079

System

Error

Check back error, verification of stop control

E0080

System

Error

Check back error, stop verification

E0081

System

Error

Check back error, operation verification

E0082

System

Error

Current programmed on P401 (and P402) out of the UMC/
UMCT range

E0085

System

Error

Without communication with the UMC/UMCT

E0087

Protection

Trip

Trip Test

E0088

Protection

Trip or alarm

External fault

E0089

Protection

Trip or alarm

Underpower

E0090

Protection

Trip or alarm

Overpower

E0091

Protection

Trip or alarm

Power under factor

E0092

Protection

Trip or alarm

Power over factor

E0129

System

Error or fault

Ethernet offline

E0130

System

Error or fault

Ethernet interface access error

E0131

System

Error or fault

Modbus communication timeout

E0150 to

E0199

System

Error or fault

WLP user errors

(*)

HMI local error is not registered in the SRW01-UC if P220 or P232 ≠ 1.

(**)

It signals error if the motor is OFF and does not allow driving it. If the motor is on, it signals alarm.

Содержание SRW 01





















































































































































Результаты поиска

Содержание SRW 01

Отзывы:

Похожие инструкции для SRW 01

Бренды по названию

Популярные бренды

WEG SRW 01, Руководство пользователя

Результаты поиска

Содержание SRW 01

Отзывы:

Похожие инструкции для SRW 01

Бренды по названию

Популярные бренды