Weco Discovery 300 AC/DC Скачать руководство пользователя страница 8

Страница: 8 / 34

Cod.006.0001.1840
13/07/2016 v2.2

ENGLISH

Discovery 300 AC/DC

8/34

USER INTERFACE

CODE

SYMBOL

DESCRIPTION

DC TIG mode:

Illumination shows that the following function has been activated: Q-START

AC TIG mode:

Illumination shows that the following function has been activated: AC WAVE IN MIX AC-DC

DC TIG mode:

Illumination shows that the following function has been activated: DYNAMIC ARC

AC TIG mode:

Illumination shows that the following function has been activated: FUSIONE EXTRA

DC TIG mode:

Illumination shows that the following function has been activated: MULTI TACK

AC TIG mode:

When this LED illuminates the following parameter can be set: AC FREQUENCY

AC TIG mode:

When this LED illuminates the following parameter can be set: AC TIG BALANCE

AC TIG mode:

When this LED illuminates the following parameter can be set: ELECTRODE DIAMETER

This LED illuminates to confirm the presence of power on the output sockets.

This LED illuminates to show an anomaly in the operating conditions.

See “ALARMS MANAGEMENT”(§ 9 page 12).

This LED illuminates to show that the following welding mode is selected: TIG PULSED

DC TIG mode:

When this LED illuminates the following parameter can be set: TIG SYNERGIC PULSE

When this is on, it means that the synergic mode is active and that the operator can set just the welding current while the other parameters are
automatically regulated by the machine. The synergy is optimised by angle welding.

Illumination shows that the following function has been activated: High frequency arc strike (HF)

This LED indicates that the current reference setting is imposed by the remote controller.

L10

Illumination shows that the following function has been activated: 2 times procedure

§ 13.1 page 24 / § 13.2 page 24

A flashing signal means the following function is activated: 2 times procedure

§ 13.7 page 26 / § 13.8 page 26

L11

Illumination shows that the following function has been activated: 4 times procedure

§ 13.3 page 24 / § 13.4 page 25

L12

Illumination shows that the following function has been activated: 4 times Bi-level procedure

§ 13.5 page 25 / § 13.6 page 25

L13

This LED illuminates to show that the following welding mode is selected: MMA

L14

This LED illuminates to show that the following welding mode is selected: TIG CONTINUOUS

L15

This LED illuminates to show that the following welding mode is selected: AC TIG

Parameters/functions setting:

The displays show the value of the following parameter: WELDING CURRENT

Welding:

The display shows the effective amperes value during welding.

HOLD function:

The display shows the latest measured current value.

Содержание Discovery 300 AC/DC



































Результаты поиска

Содержание Discovery 300 AC/DC

Отзывы:

Похожие инструкции для Discovery 300 AC/DC

Бренды по названию

Популярные бренды

Weco Discovery 300 AC/DC, Инструкция по эксплуатации

Результаты поиска

Содержание Discovery 300 AC/DC

Отзывы:

Похожие инструкции для Discovery 300 AC/DC

Бренды по названию

Популярные бренды