Weco Discovery 300 AC/DC, Инструкция по эксплуатации

Страница: 3 / 34

Discovery 300 AC/DC
Cod.006.0001.1840
13/07/2016 v2.2
ENGLISH
0
3/34
1 INTRODUCTION ................................................................. 4
2 FRONT PANEL ................................................................... 4
3 REAR PANEL ..................................................................... 5
4 INSTALLATION .................................................................. 5
4.1 CONNECTIONS TO THE ELECTRICAL MAINS NETWORK 5
4.2 PREPARING FOR MMA WELDING ..................................... 5
4.3 PREPARING FOR TIG WELDING ....................................... 6
5 USER INTERFACE ............................................................. 8
6 UNIT POWER-UP ............................................................... 9
7 RESET (LOAD FACTORY SETTINGS) ............................... 9
7.1 PARTIAL RESET................................................................. 9
7.2 TOTAL RESET .................................................................. 10
8 SET-UP (INITIAL SET-UP OF THE WELDING POWER
SOURCE) ......................................................................... 10
8.1 TORCH LOADING ............................................................. 12
9 ALARMS MANAGEMENT ................................................. 12
THERMAL ALARM! ...............................................................................12
COOLING DEVICE ALARM..................................................................12
10 WELDING PARAMETERS ................................................ 13
Welding current ......................................................................................13
Max welding current...............................................................................13
Hot-start ..................................................................................................13
Arc-force..................................................................................................13
VRD .........................................................................................................13
Long arc voltage.....................................................................................13
Remote control .......................................................................................13
Dynamic arc ............................................................................................13
Second current Bi-level .........................................................................13
Base current ...........................................................................................13
Peak time ................................................................................................14
Base time ................................................................................................14
Pulse frequency......................................................................................14
Slope down .............................................................................................14
Final current ............................................................................................14
Post-gas ..................................................................................................14
Pre-gas....................................................................................................14
Start current ............................................................................................14
Slope up ..................................................................................................14
Spot TIG time .........................................................................................14
HF arc start .............................................................................................14
Minimum pedal current ..........................................................................14
Q-start .....................................................................................................14
Multi-tack.................................................................................................14
AC wave in mix AC-DC .........................................................................14
Extra fusion .............................................................................................14
AC frequency ..........................................................................................15
AC balance .............................................................................................15
Electrode diameter .................................................................................15
10.1 PARAMETERS ACTIVATION ............................................ 16
11 WELDING SETTINGS ....................................................... 18
11.1 ELECTRODE WELDING (MMA) ........................................ 18
11.1.1 MMA PARAMETERS SETTING (1ST LEVEL) ...................................18
11.1.2 MMA PARAMETERS SETTING (2ND LEVEL)...................................18
11.1.3 MMA SPECIAL FUNCTIONS ...............................................................18
11.2 DC TIG WELDING ............................................................. 19
11.2.1 DC TIG PARAMETERS SETTING (1ST LEVEL) ...............................19
11.2.2 DC TIG PARAMETERS SETTING (2ND LEVEL) ..............................19
11.2.3 DC TIG SPECIAL FUNCTIONS MENU ...............................................20
11.3 AC TIG WELDING ............................................................. 21
11.3.1 AC TIG PARAMETERS SETTING (1ST LEVEL) ...............................21
11.3.2 AC TIG PARAMETERS SETTING (2ND LEVEL)...............................21
11.3.3 AC TIG SPECIAL FUNCTIONS MENU ...............................................22
12 JOBS MANAGEMENT ...................................................... 23
12.1 SAVING A JOB ................................................................. 23
12.2 LOADING A USER JOB OF FACTORY SET JOB .............. 23
12.3 DELETING A JOB ............................................................. 23
13 TORCH TRIGGER MODES ............................................... 24
13.1 2T LIFT-ARC WELDING .................................................... 24
13.2 2T HF WELDING ............................................................... 24
13.3 4T LIFT-ARC WELDING..................................................... 24
13.4 4T HF WELDING ............................................................... 25
13.5 BI-LEVEL LIFT WELDING .................................................. 25
13.6 BI-LEVEL HF WELDING .................................................... 25
13.7 2T SPOT WELDING........................................................... 25
13.8 2T SPOT HF WELDING ..................................................... 26
13.9 PILOT ARC WELDING ....................................................... 26
14 TECHNICAL DATA............................................................ 27
15 SPARE PARTS ................................................................. 28
16 ELECTRICAL DIAGRAM ................................................... 30
16.1 DISCOVERY 300 AC/DC ................................................... 30
16.2 TORCH CONNECTOR....................................................... 32
16.3 REMOTE CONTROLLER CONNECTOR ............................ 32