manualshive.com logo in svg

Weco Discovery 221AC/DC Evo, Инструкция по эксплуатации

Поделиться
Скачать
Weco Discovery 221AC/DC Evo Скачать руководство пользователя страница 53

WELD THE WORLD

Cod. 006.0001.2000

19/07/2018 V.2.0

Discovery 221AC/DC Evo

Discovery 300AC/DC Evo

53

ENGLISH

1. Position the torch 

with the electrode on 

the workpiece.

2. Press the torch 

trigger and keep it 

pressed.

3. Lift the torch 

slightly.

As soon as the 

electrode is lifted 

then the HF ignition 

starts.

4. The arc ignites for 

A few hundredths of 

a second (time can 

be set up).

5. The result of this 

is  a  very  precise, 

not  oxidized  weld

-

ing spot without any 

plastic deformation 

of the sheet.

PROCEDURE WITH CONTINUOUS PRESSURE OF  TORCH BUTTON

 

○ Bring the torch up to the work until the electrode tip is approximately 2 or 3 mm away.

 

○

Press (1T) the torch trigger.

 

○ The arc strikes without contact with the workpiece and the voltage discharges (HF) cease auto

-

matically.

 

○ The welding current reaches the pre-set value, by way of an up slope time, if programmed.

 

○ The welding procedure continues, at the pre-set current, for the time set with the spot time pa

-

rameter.

 

○ The current reaches the end current value in the time set in the down slope time parameter.

 

○

The arc is extinguished.

 

○ Gas delivery continues for the time set in the post gas parameter.

 

○ Touch the workpiece with the torch electrode.

 

○ Slowly lift the torch to strike the arc.

The welding parameters are available in accordance with the selected welding mode and procedure.

Certain parameters are available only after other parameters or functions of the unit have been enabled 

or set.

The table shows the settings required to enable each parameter.

LEGEND

√: 

  ____

Always available.

1: 

  ____

Available with the following setting: MULTI TACK = OFF

2:

  ____

Available when remote control is enabled and a remote control pedal is connected to the 

unit.

3:  

 ____

Available with the following setting: 

HF STRIKE

 = ON

4: 

  ____

Available when foot pedal controller is disabled.

5:  

 ____

Available with the following setting: TYPE OF PULSED CURRENT = SLO.

6:  

 ____

Available with the following setting: TYPE OF PULSED CURRENT = FA.

Meaning of symbols

1+2

 = All conditions must be fulfilled (both 1 and 2).

Antwerpsesteenweg 949 9041 Gent - Oostakker
[email protected]
www.welda.be

T

   +32 (0)9 355 74 26

F

   +32 (0)9 355 92 01

Содержание Discovery 221AC/DC Evo









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды