manualshive.com logo in svg

Weco Discovery 221AC/DC Evo, Инструкция по эксплуатации

Поделиться
Скачать
Weco Discovery 221AC/DC Evo Скачать руководство пользователя страница 18

WELD THE WORLD

Cod. 006.0001.2000

19/07/2018 V.2.0

Discovery 221AC/DC Evo

Discovery 300AC/DC Evo

18

ENGLISH

SET UP
POWER ON

7.2 h

The  reading  is  carried  out  as  follows:  7  hours  and  (0.2x60) 

12 minutes

T. ARC. ON

5.3 h

P. ARC ON

0.7 h

- 

RESET

 

○ The reset procedure involves complete restoration of the default values, parameters and memory 

settings set in the factory.

 

○ The reset procedure is useful in the following cases:

• 

Too many changes made to the welding parameters so user finds it difficult to restore defaults.

• 

Unidentified software problems that prevent the welding power source from functioning cor

-

rectly.

 

PARTIAL RESET

The reset procedure involves restoration of the parameter values and settings, except the following 

settings:

•  Settings of the SETUP menu.

• 

Saved JOBS

TOTAL RESET 

• 

The reset procedure involves complete restoration of the default values, parameters and me

-

mory settings set in the factory.

• 

All memory locations will be reset and hence all your personal welding settings will be lost!

-

 

SERVICE

 

○ his setting enables the machine validation (VAL.) and calibration (CAL) operations.

VALIDATION

 

○ The validation procedure allows the welding current value (Ampere) and voltage value (Volt) to 

be correctly detected and displayed on the equipment display. The validation procedure requires 

the equipment to be connected to a suitable static load.

CALIBRATION

 

○ he calibration procedure allows the machine current to be calibrated. 

The SERVICE procedure is not described in this manual as it can be carried out only by specialised, 

suitably trained and equipped technical staff.

The testing methods and the equipment required are set out in the relevant technical standards.

.

Antwerpsesteenweg 949 9041 Gent - Oostakker
[email protected]
www.welda.be

T

   +32 (0)9 355 74 26

F

   +32 (0)9 355 92 01

Содержание Discovery 221AC/DC Evo









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды