Weber mt SRV 650 Скачать руководство пользователя | Manualshive

Страница: 7 / 24

background image

SRV

650

7

inspection

Tampers must be inspected in accordance with appropriate implementation conditions and operating

conditions, as needed; however an inspection to ensure operationally safe status must be performed

by an expert at least once a year. The results of the inspection must be recorded in writing and must

be stored at least until the next inspection.

cleaning work

Prior to cleaning the tamper with a high-pressure cleaner, protect all accessible energized switches,

cable connections, etc. against water penetration by masking them off.

Cleaning tasks should only be executed in areas that are suitable and have been approved for this

purpose (oil separator amongst others).

disposal

All operating fluids and auxiliary materials must be disposed of in an environmentally-compatible

manner in accordance with country-specific regulations.

Warning against irritants or materials hazardous to health

Warning against a hazardous place

Warning against a suspended load

Wear ear protection

General regulation

Environmental protection

important information for operating and maintenance personnel is marked by pictograms.

Hard hat

Safety shoes

Protective gloves

«
...
5
6
7
8
9
...
»

Содержание SRV 650

























Отзывы:

Нет отзывов

Похожие инструкции для SRV 650

Бренд: Chicago Pneumatic Страницы: 224

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды